Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

SNMP for monitoring BGP routes

Is there any way by which we can find the number of routes and number of received routes using snmpget.

OID - 1.3.6.1.4.1.9.9.187.1.2.4.1.1 gives us information about the routes accepted after appling filters. But is there and OID for received-routes for a neighbour.

5 REPLIES
Cisco Employee

Re: SNMP for monitoring BGP routes

May have to get two OIDs and use the sum of Accepted, Denied prefixes.

CISCO-BGP4-MIB::cbgpPeerAcceptedPrefixes.192.168.1.2.ipv4.unicast = Counter32: 15

CISCO-BGP4-MIB::cbgpPeerDeniedPrefixes.192.168.1.2.ipv4.unicast = Gauge32: 2

HTH,

Dan

New Member

Re: SNMP for monitoring BGP routes

Hi Dan,

Thanks, but I still have doubts if this will give the correct value.

If i have a neighbour 192.168.1.2.

enterprises.9.9.187.1.2.4.1.1.63.243.149.110.1.1 = Counter32: gives me the same value which i get in sh ip bgp nei 192.168.1.2 routes .

But cbgpPeerDeniedPrefixes ( 1.3.6.1.4.1.9.9.187.1.2.4.1.2) gives relative value which is not euivalent to ( accepted+denied)

Suggestion ..

Cisco Employee

Re: SNMP for monitoring BGP routes

Could you post the values for these OIDs:

CISCO-BGP4-MIB::cbgpPeerAcceptedPrefixes.192.168.1.2.ipv4.unicast = Counter32: 15

CISCO-BGP4-MIB::cbgpPeerDeniedPrefixes.192.168.1.2.ipv4.unicast = Gauge32: 2

CISCO-BGP4-MIB::cbgpPeerPrefixAdminLimit.192.168.1.2.ipv4.unicast = Gauge32: 0

CISCO-BGP4-MIB::cbgpPeerPrefixThreshold.192.168.1.2.ipv4.unicast = Gauge32: 0

CISCO-BGP4-MIB::cbgpPeerPrefixClearThreshold.192.168.1.2.ipv4.unicast = Gauge32: 0

CISCO-BGP4-MIB::cbgpPeerAdvertisedPrefixes.192.168.1.2.ipv4.unicast = Gauge32: 17

CISCO-BGP4-MIB::cbgpPeerSuppressedPrefixes.192.168.1.2.ipv4.unicast = Gauge32: 0

CISCO-BGP4-MIB::cbgpPeerWithdrawnPrefixes.192.168.1.2.ipv4.unicast = Gauge32: 0

Also post the "Total number of prefixs" shown by the "show ip bgp neigh 192.168.1.2" command

Thanks,

Dan

New Member

Re: SNMP for monitoring BGP routes

SNMPv2-SMI::enterprises.9.9.187.1.2.4.1.1.192.168.1.2.1.1 = Counter32: 151

SNMPv2-SMI::enterprises.9.9.187.1.2.4.1.2.192.168.1.2.1.1 = Gauge32: 2521

SNMPv2-SMI::enterprises.9.9.187.1.2.4.1.3.192.168.1.2.1.1 = Gauge32: 0

SNMPv2-SMI::enterprises.9.9.187.1.2.4.1.4.192.168.1.2.1.1 = Gauge32: 0

SNMPv2-SMI::enterprises.9.9.187.1.2.4.1.5.192.168.1.2.1.1 = Gauge32: 0

SNMPv2-SMI::enterprises.9.9.187.1.2.4.1.6.192.168.1.2.1.1 = Gauge32: 2213402

SNMPv2-SMI::enterprises.9.9.187.1.2.4.1.7.192.168.1.2.1.1 = Gauge32: 108514

SNMPv2-SMI::enterprises.9.9.187.1.2.4.1.8.192.168.1.2.1.1 = Gauge32: 986169

sh ip bgp neighbors 192.168.1.2

Sent Rcvd

Prefix activity: ---- ----

Prefixes Current: 55785 151 (Consumes 8424 bytes)

Prefixes Total: 2213421 1822

Implicit Withdraw: 1220931 1649

Explicit Withdraw: 986180 22

Used as bestpath: n/a 34

Used as multipath: n/a 34

Saved (soft-reconfig): n/a 84 (Consumes 4368 bytes)

New Member

SNMP for monitoring BGP routes

can you please guide me how can i get these statistics for IPv6 BGP peers?

5825
Views
0
Helpful
5
Replies