Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

SNMP OIDs for ASR1k

Hi everyone,

We're trying to read CPU & MEM values from ASR1006 equipment. Obviously the old OIDs are not supported on this platform. This is what we have found by going through the snmp object navigator. (I assume .2 is the ESP, .3 is the RP, .4 & .5 are the SIPs). But the values we get from the command line are slightly different than what we get through snmp. Has anyone done this before? What OIDs do you use?

=====================================================================

CPU:

1min: cpmCPULoadAvg1min

Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.24.2; Value (Gauge):

Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.24.3; Value (Gauge):

Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.24.4; Value (Gauge):

Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.24.5; Value (Gauge):

5min: cpmCPULoadAvg5min
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.25.2; Value (Gauge):
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.25.3; Value (Gauge):
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.25.4; Value (Gauge):
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.25.5; Value (Gauge):

15min: cpmCPULoadAvg15min
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.26.2; Value (Gauge):
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.26.3; Value (Gauge):
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.26.4; Value (Gauge):
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.26.5; Value (Gauge):

======================================================================
Memory:

cpmCPUMemoryUsed
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.12.2; Value (Gauge): KiloByte
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.12.3; Value (Gauge): KiloByte
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.12.4; Value (Gauge): KiloByte
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.12.5; Value (Gauge): KiloByte

cpmCPUMemoryFree
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.13.2; Value (Gauge): KiloByte
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.13.3; Value (Gauge): KiloByte
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.13.4; Value (Gauge): KiloByte
Name/OID: .1.3.6.1.4.1.9.9.109.1.1.1.1.13.5; Value (Gauge): KiloByte

Best Regards,

Babak  

Everyone's tags (7)
2 REPLIES
New Member

Hi Babek,On the contrary I

Hi Babek,

On the contrary I believe the last value of the IOD related to the slot number.

We have 2 SIP, One in slot 1 (the top most in our 1006) and One in slot 3.

These are the IODs we use for these:

.1.3.6.1.4.1.9.9.109.1.1.1.1.13.7 = SIP0 - Free Memory

.1.3.6.1.4.1.9.9.109.1.1.1.1.13.5 = SIP2 - Free Memory

Hope this helps

Peter Haas

Silver

Calculating Memory

Calculating Memory Utilization:

cempMemPoolUsed 1.3.6.1.4.1.9.9.221.1.1.1.1.7

cempMemPoolFree 1.3.6.1.4.1.9.9.221.1.1.1.1.8

Memory Utilization = cempMemPoolUsed /( cempMemPoolUsed  + cempMemPoolFree)] * 100

Recommended threshold for Memory Utilization is 80%

911
Views
0
Helpful
2
Replies
CreatePlease login to create content