Cisco Support Community
Showing results for 
Search instead for 
Did you mean: 
New Member

Snmp Version2 on Cat 6 supported ?

Hi All,

I use this H/W

System image file is "sup-bootdisk:s72033-ipservices_wan-mz.122-18.SXF5.bin"

cisco WS-C6504-E (R7000) processor (revision 2.0) with 983008K/65536K bytes of memory.

When doing snmpwalk using SNMP version 1 get response as follows:

[cacti@localhost cacti]# snmpwalk -v 1 -c MyString x.x.x.x .

IF-MIB::ifDescr.1 = STRING: GigabitEthernet1/1

IF-MIB::ifDescr.2 = STRING: GigabitEthernet1/2

IF-MIB::ifDescr.3 = STRING: GigabitEthernet3/1

IF-MIB::ifDescr.4 = STRING: GigabitEthernet3/2

IF-MIB::ifDescr.5 = STRING: GigabitEthernet3/3

--- cut ---

But if use SNMP the version 2 , seems not responding (shown "Time Out")

[cacti@localhost cacti]# snmpwalk -v 2c -c MyString x.x.x.x .

Timeout: No Response from x.x.x.x

Any idea is it because My Cat 6 doesn't support SNMP version 2, any advice?



Cisco Employee

Re: Snmp Version2 on Cat 6 supported ?

SNMPv2c is supported with no additional configuration. I don't know of any bugs which would cause this. If you enable "debug snmp packet" on the device then run the test, what output do you see?

Re: Snmp Version2 on Cat 6 supported ?

Can you also post your show run?

New Member

Re: Snmp Version2 on Cat 6 supported ?


This is the current snmp config

Router1#sh ru | i snmp

snmp-server view v1default internet included

snmp-server view v1default at excluded

snmp-server view v1default ip.21 excluded

snmp-server view v1default ip.22 excluded

snmp-server community MyString1 RO 1

snmp-server community MyString2 RO 1

snmp-server community MyString3 view v1default RO 1

snmp-server community MyString4 RW 1

snmp-server trap-source VlanXX

snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart

snmp-server enable traps casa

snmp-server enable traps tty

snmp-server enable traps bgp

snmp-server enable traps config

snmp-server enable traps dlsw

snmp-server enable traps frame-relay

snmp-server enable traps hsrp

snmp-server enable traps ipmulticast

snmp-server enable traps msdp

snmp-server enable traps rtr

snmp-server enable traps syslog

snmp-server enable traps dial

snmp-server enable traps entity

snmp-server enable traps rsvp

snmp-server enable traps envmon fan shutdown supply temperature status

snmp-server enable traps voice poor-qov

snmp-server host x.x.x.x MyString1

The backgorup of using the SNMP ver 2 is to configure our NMS-cacti in order to

support traffic monitoring more than 100 Mbps. The only solution that we need is to set snmp ver 2 ( which supports 64 bit).



Cisco Employee

Re: Snmp Version2 on Cat 6 supported ?

What community string are you using now? I would strongly recommend you remove all the v1default view customizations. If you need a custom view, create a new one. Do not override v1default.

Also, can you post the output of "debug snmp packet" when reproducing this problem?

New Member

Re: Snmp Version2 on Cat 6 supported ?


I removed all v1 default as suggested, but snmp ver still wasn't not working.

If I issue this command:

"debug snmp packet"

How much utilization taken by this proccess?

Because the current unit is running on production.



Cisco Employee

Re: Snmp Version2 on Cat 6 supported ?

It depends on the amount of SNMP traffic the device is receiving. If a lot of polling is being done, then it can increase device load substantially.

New Member

Re: Snmp Version2 on Cat 6 supported ?


Any other alternative solution? Since you confirmed that the current IOS is being used can still support snmp ver 2.



Cisco Employee

Re: Snmp Version2 on Cat 6 supported ?

Without seeing how the packets are being interpreted by the switch, I cannot say why this is happening. I cannot reproduce internally. You might try increasing the SNMP timeout in your snmpwalk tool. Try 10 seconds to see if it makes a difference.

CreatePlease to create content