Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

%STANDBY-3-DUPADDR: Duplicate address

I am getting continuos error on my core switches where i am running hsrp.... the MAC reporting as Duplicate is the Virtual MAC of HSRP. I have read the Documentation where cisco is talking about STP & Mulfunctioning of the switch. I have tested for the STP loops but i did not find any. How i could check whether my switch is proper or malfunctioning, as i dont see any problem, the core switches are 4507R. find below the error message.

Vlan8, sourced by 000d.2822.f57f

.Jan 3 01:22:17.834 SA: %STANDBY-3-DUPADDR: Duplicate address 132.1.1.251 on Vl

an1, sourced by 0000.0c07.ac00

.Jan 3 01:50:43.226 SA: %STANDBY-3-DUPADDR: Duplicate address 10.0.160.2 on Vla

n11, sourced by 0000.0c07.ac00

.Jan 3 01:51:40.778 SA: %STANDBY-3-DUPADDR: Duplicate address 10.0.80.2 on Vlan

6, sourced by 0000.0c07.ac00

.Jan 3 02:00:43.142 SA: %STANDBY-3-DUPADDR: Duplicate address 10.0.48.2 on Vlan

4, sourced by 0000.0c07.ac00

.Jan 3 02:02:54.930 SA: %STANDBY-3-DUPADDR: Duplicate address 10.40.1.2 on Vlan

40, sourced by 0000.0c07.ac00

.Jan 3 02:05:59.782 SA: %STANDBY-3-DUPADDR: Duplicate address 10.1.32.2 on Vlan

22, sourced by 0000.0c07.ac00

.Jan 3 02:44:14.190 SA: %STANDBY-3-DUPADDR: Duplicate address 10.0.16.2 on Vlan

2, sourced by 0000.0c07.ac00

.Jan 3 02:57:19.330 SA: %STANDBY-3-DUPADDR: Duplicate address 10.40.1.2 on Vlan

40, sourced by 0000.0c07.ac00

.Jan 3 03:25:30.578 SA: %STANDBY-3-DUPADDR: Duplicate address 10.0.112.2 on Vla

n8, sourced by 000d.2822.f57f

.Jan 3 03:34:35.917 SA: %STANDBY-3-DUPADDR: Duplicate address 10.1.16.2 on Vlan

21, sourced by 0000.0c07.ac00

.Jan 3 03:37:49.661 SA: %STANDBY-3-DUPADDR: Duplicate address 132.1.1.251 on Vl

1 REPLY

Re: %STANDBY-3-DUPADDR: Duplicate address

Hi,

The error message not necessary HSRP problem. Since the error received by the HSRP VIP MAC Address, this suggest a router or switch configuration problem that may cause the one or more of the following;

1. Momentary STP Loop

- make sure you follow recommended configuration to prevent/avoid STP Loop. i.e. assign primary and secondary root bridge

2. Etherchannel misconfiguration problem

- check the config and logs

3. Both routers in HSRP group is in Active state

- check both routers HSRP status and interface status whether its flapping. i.e. show standby, show ip int brief

Regards,

Dandy

516
Views
0
Helpful
1
Replies
CreatePlease login to create content