Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

what is the possible cause of having always is disconnected in the network?

I have been trouble in my network for almost a week and i didn't figure out what is the cause of intermittent connection 2 of my client with windows 7 installed.

I'm using WS-C3550 Cisco Switch on HQ, configure as trunk the port #1 which is UBNT Wireless is inserted.  on branch A i'm using cisco 2960, in port gi0/1 UBNT Wireless is inserted, meaning we are using wireless connectivity to link this two sites. My problem is 2 computer is always disconnect in the network with a certain time, I already replace the Ethernet cable, change the speed and duplex but same problem occurred. but other PC with XP OS installed with no problem. i just want to know if there are protocol not compatible between PC to cisco switch.

Here are some details

HQ

SWRouter#show int fa 0/1
FastEthernet0/1 is up, line protocol is up (connected)
  Hardware is Fast Ethernet, address is 000d.2848.a901 (bia 000d.2848.a901)
  MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
     reliability 255/255, txload 1/255, rxload 2/255
  Encapsulation ARPA, loopback not set
  Keepalive set (10 sec)
  Full-duplex, 100Mb/s, media type is 10/100BaseTX
  input flow-control is off, output flow-control is unsupported
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input 00:00:00, output 00:00:00, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 1056000 bits/sec, 144 packets/sec
  5 minute output rate 475000 bits/sec, 110 packets/sec
     11580406 packets input, 2116489376 bytes, 0 no buffer
     Received 3058656 broadcasts (0 multicasts)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog, 1239883 multicast, 0 pause input
     0 input packets with dribble condition detected
     27734460 packets output, 3476907667 bytes, 0 underruns
     0 output errors, 0 collisions, 1 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier, 0 PAUSE output
     0 output buffer failures, 0 output buffers swapped out

-------------------------------------------------

BRANCH A

 

Pricesmart_Dacera>show int gi 0/1
GigabitEthernet0/1 is up, line protocol is up (connected)
  Hardware is Gigabit Ethernet, address is 3c0e.233c.d399 (bia 3c0e.233c.d399)
  MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive not set
  Full-duplex, 100Mb/s, link type is auto, media type is 10/100/1000BaseTX
  input flow-control is off, output flow-control is unsupported
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input 00:00:00, output 00:00:00, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 74000 bits/sec, 35 packets/sec
  5 minute output rate 11000 bits/sec, 13 packets/sec
     4464105 packets input, 1092571901 bytes, 0 no buffer
     Received 2606921 broadcasts (921122 multicasts)
     1 runts, 0 giants, 0 throttles
     1 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog, 921122 multicast, 0 pause input
     0 input packets with dribble condition detected
     2113803 packets output, 331286478 bytes, 0 underruns
     0 output errors, 0 collisions, 1 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier, 0 PAUSE output
     0 output buffer failures, 0 output buffers swapped out

-----------------------------------------

PORT of PC1 which has been always disconnected every 30 or 1 hour.

Pricesmart_Dacera>show int fa 0/8
FastEthernet0/8 is up, line protocol is up (connected)
  Hardware is Fast Ethernet, address is 3c0e.233c.d388 (bia 3c0e.233c.d388)
  MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive set (10 sec)
  Full-duplex, 100Mb/s, media type is 10/100BaseTX
  input flow-control is off, output flow-control is unsupported
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input never, output 00:00:00, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 5000 bits/sec, 2 packets/sec
  5 minute output rate 93000 bits/sec, 32 packets/sec
     466896 packets input, 100716636 bytes, 0 no buffer
     Received 76760 broadcasts (4823 multicasts)
     0 runts, 0 giants, 0 throttles
     20 input errors, 20 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog, 4823 multicast, 0 pause input
     0 input packets with dribble condition detected
     1635257 packets output, 483196219 bytes, 0 underruns
     0 output errors, 734 collisions, 7 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier, 0 PAUSE output
     0 output buffer failures, 0 output buffers swapped out

Thank you.

Regards,

Raffy

Everyone's tags (1)
3 REPLIES
Hall of Fame Super Gold

20 input errors, 20 CRC, 0

20 input errors, 20 CRC, 0 frame, 0 overrun, 0 ignored
 0 output errors, 734 collisions, 7 interface resets

Can you tell us what is the uptime of the switches?  Fa0/8 is showing duplex errors.  Someone has hard-coded speed/duplex settings on either the switch port or the PC (or both)?

New Member

Pricesmart_Dacera uptime is 4


Pricesmart_Dacera uptime is 4 days, 8 hours, 26 minutes
System returned to ROM by power-on
System image file is "flash:/c2960-lanbasek9-mz.122-55.SE7/c2960-lanbasek9-mz.12
2-55.SE7.bin" i try to hard-code the port# 8 to solve the problem but it can't.

Hall of Fame Super Gold

Post the "sh interface"

Post the "sh interface" output of the port connected to the PC again.  I want to see if the port has line error incrementing.

135
Views
2
Helpful
3
Replies