Hello, we recently updgrade CSM to 4.3.0 service pack2 and we figure out that objet are duplicated with _xx when push are perform to FW asa version 8.4.How i can resolve the problem in order to avoid this duplicated objets.
In the 'Home' page of the ASDM, there is the 'Interface Status' box that shows the status of each interface and how much bandwidth each one is using. Is there any place in the ASDM that I'm missing that can show real-time bandwidth usage for each of ...
HiI am looking to disable ACL optimization on a single context as part of a strategy to 'clean up' the firewall rule base.I was wondering if anyone had done this before and what there experience was. I would specifically like to know if it is likely ...
I have one external ip address of 200.200.200.200. Then i have two different servers. One server is running https and smtp. I'm able to create my acls and static mappings to get that working. Now the second server i have about ALOT of ports (10000 -...
Hi,We are looking at doing a 2Factor authentication for certain server bound traffic using asa. the requirements are, asa should prompt for 2 factor authentication when admin users login to the servers ( hosted behind the firewall ) using telnet/rdp....
I have a Cisco ASA firewall that is setup with an inside interface and a DMZ interface. I also have a Websense content filter that is currently filtering traffic succesfully on the inside interface.I setup a DMZ port for our guest wireless network a...
Okay so here is my network setup. I have a 1 ASA5505 setup at a remote location. My internet/voice provider has a router at that location also to route traffic over the MPLS for our location to location traffic, and to route traffic to the internet. ...
Hello!I am attempting to allow a single host to NOT be sent to the Ironport. It's a Linux box that needs to get to download.opensuse.org. I've tried adding an access list for that host, to an inet host via any IP. The traffice still goes to the Ironp...
Hi everyone,If this has been posted before, which it probably has, I apologize in advance.Basically, I have to configure a VPN between our NY ASA and a PIX we shipped to our LA office. The PIX is replacing an old Cisco router. The ASA is our main dev...
In a recent Cisco Security Advisory (Advisory ID: cisco-sa-20131009-asa) there is a "SQL*Net Inspection Engine Denial of Service Vulnerability" identified. I plan to follow the upgrade process to resolve this, however, I will not be able to perform ...
Hi, Just a clarification on Proxy ARP on ASAs. Scenario: Web Server 10.1.1.1 -- in ---- ASA ---- out ----- InternetLet's say the WWW server has real IP 10.1.1.1 and static NAT 200.1.1.2ASA's outside IP is 200.1.1.1When traffic comes from the Interne...
Hi all!I have deployed an ASA5512-IPS-K9 unit that has the following 2 licenses installed:Cisco ASA 5512 SW License Security PlusCisco ASA 5512 SW License IPS SSP LicenseAll is working out fine except for the IPS SW module.When viewing the IPS using ...
Hello everyone,I am trying to use the Cisco SDM version 2.5. I installed the software on a PC running Windows XP service pack 3. When I launch the application, I get the screen shown below. I have no idea what I may have done wrongly. Please help...
Here is the situation. I have the VPN anyconnect client connected and can access other resources like pinging the hosts, windows shares, rdp to this sql server. I just can't sql connect from an emr software (emds) into the 192.168.1.15 server ru...
Hi AllAfter some advise and directionOur ASA firewall using ASA version 8.4 has recently started presenting us with a problem to one external websitecalled http://partners.highnet.com/login/ ip address 62.233.82.181.Our firewall is letting everythin...
