HelloI am using Cisco Security Manager v3.3.0 and FWSM 3.1(7)Does anyone know the best way to nat all addresses behind the outside interface IP only, for example:Source 10.10.10.0/24Destination 10.20.20.1Outside Int 10.20.20.250I wou...
HelloI am using Cisco Security Manager v3.3.0 and FWSM 3.1(7)Does anyone know the best way to nat all addresses behind the outside interface IP only, for example:Source 10.10.10.0/24Destination 10.20.20.1Outside Int 10.20.20.250I wou...
Hi,I need a little assistance here...I'm trying to do multiple nats...The intent is to nat traffic inbound to isolated/non-routable vlans to the vlan interface to give the appearance the traffic is within the same subnet to keep a couple hundred serv...
Microsoft Security Advisory (2269637)Insecure Library Loading Could Allow Remote Code ExecutionThis vulnerability came out in August and is there a signature that will cover this in the ips and if not is there an idea if one is being reviewed?
I have an SBS 2008 server with exchange server and I am trying to route my mail to my internal server. My config and domain info is attached. Thanks for your assistance,ISP has given me xx.xx.xx.120 as public IP Block, xx.xx.xx.121 as Gateway and xx....
Hello everyone,I have a pix525e and users of the various interfaces (inside, dmz, inside1) go out on the Internet through a pool of public IP or by using the command ip static public static(inside, outside) internal_ip external_ip.as a matter of nece...
Hello,I have 2811 Series Router with C2800NM-ADVIPSERVICESK9-M), Version 12.4(20)Tmy config is :ETH1 : inside 192.168.1.10S0/0/0 : outside Encap PPP, outiside 41.12.110.165CBAC applied on S0/0/0 (inspect out)Inbound access list applied S0/0/0 to perm...
Hi there!I have been trying to establish a VPN connection between Windows 7 Ultimate client and Windows Server 2008.I am using L2TP over IPSEC and in the middle I have a Cisco ASA5505 with version 8.2(1).The ASA is doing NAT 1:1 and I have openned ud...
Hello all I'm very new to cisco and am looking for some advice on the following setup.Here is our network setup:Internet <----- ASA5510<---> Cisco 300 switch (2) <---->LAN clients | ...
Hi folkswhat is the means in WCS monitoring Roaming reason unspecifiedthen the user will be disconnected thanks
If I upgrade ASA code (from 8.3.2 to 8.4.1) on the primary 5540, will the secondary 5540 code automatically be upgraded? If so, is it through the failover link?
Hi,I'm taking the plunge with a client tommorrow on ASA 8.4(1) code (a new install, not an upgrade). and was wondering if anyone out there had any experiences, good or bad, to share about this revision?From the release notes, it seems to address over...
All, I am configuring some ASA5510s with AIP-SSM IPS cards, and would like to alert busy operators with an audible alert for events above some defined threshold. I don't see any built-in audible alert options in either IME or ASDM. Does anyone ...
Hi everybody,you can find here a schema and fw confs: https://supportforums.cisco.com/message/3289161I faced another problem related to the above infrastructure.I've added to fw BBB and CCC also the appropriate ACL for the TFTP server that's in the s...
Hi all,I am currently working on a migration of a pix 515E 6.3(3) to an ASA5510 running 8.3(1).On the pix I have this NAT config:global (outside) 1 interfacenat (inside) 0 access-list nonatThis nonat access-list has more than 200 entries.If I underst...
If i have configured snmpv3 on routers and i forgot the snmp authentication and other related security parameters is there a way to recover them , i think the running-config is not displaying them . or i have to reconfigure them ?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-26-2024 02:14 AM | ||
04-22-2024 06:41 AM | ||
04-21-2024 09:36 PM | ||
04-17-2024 12:36 PM | ||
04-17-2024 07:38 AM |
User | Count |
---|---|
10 | |
6 | |
4 | |
3 | |
3 |