How do I convert Watchguard F/W rules to ASA? I know about the SCT Tool, but it is only for Checkpoint. Is there anything similar? IF not, what is the BEST manual way to convert the rules so the ASA will understand.
Hi,We bought a brand new ASA 5550 with a 4GE SSM Module.The problem is that whenever i connect to the SSM Module, it is physically up, but it cannot detect the PC that is connected to it. The isolation I've done is to try the same configuration done ...
HI,I want to measure and monitor how much bandwidth a pc consumes , when a user enters his username and password annd passes nac and conencts to the access networkHow can I monitor and check that activity and how much data exchnage takes place ?O...
Hi,I project to take an ASA5520 to support 3500 users for anti-virus, anti spam, URL Filtring...and I am not sure that ASA support proxy.is there anyone how had install the asa for requirements?thanks for your answerHassan
Hi,A server application that provides http downloads appears to be timing out after 30 minutes when going through the Asa firewall - is there a setting that can change the timeout to 60 minutes? The application timeout is 60 minutes which works when...
Hello All,I am having head office & branch office. our servers are at head office having ip address in serise 192.168.1.0.I want to establish site-to-site VPN between these 2 offices. also i want to reach some specific ports of head office server suc...
Hi All,I am implementing a Multi context ASA Firewall on our network. We have a few customers coming from the Internet via VRF's. Firewall is directly connected to the core switch which is directly connected to the Core Router (VRF) which is connecte...
Hi ,I have upgraded ASA 5510 to the latest version 8.3(2). I found one very strange issue. There is one outside_in_access entry: access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_1 any interface outsideEverytime I reloa...
Hi support,Im struck up with few cmds in 8.3 while migrated from 8.2;could you pls let me know how would i convert the below to 8.3 version..nat (server) 0 access-list nat-serveraccess-list nat-server extended deny ip object-group A-NETWORK object-gr...
I would like to setup an ASA5505 with dual ISP connections. Both of the internet connections authentication and obtain their IP address and default route using PPPOE setroute. When I have configure dual ISP support on ASA's in the past I would norma...
Hi there,Please excuse me for this simple questionI am confused about extended ACLS when we use (permit|deny) for Protocol IP,TCP,UDP on an access listI have 2 Examples below1. access-list 102 permit tcp any 192.168.10.10 ...
Remote Location (DET) has a vpn tunnel built to our main location (ML) where our websense server sits.This is the websense configuration that is in place on DET. DET local LAN is 172.20.120.0/24 access-list 50 permit any log ip inspect name we...
I have a DSL modem ( Thomson) at my home and Cisco ASA 5520. Currently the modem is used for providing internet to some PC's and its getting a DHCP ip address.So how can i configure the ASA to work with ASA ?I want to work on some practice labsPlease...
I have an ASA firewall placed at the perimeter network and host in the inside network.I have only allowed these host to make voip calls using 3rd Party Voip service so-called Jumblo ( for info www.jumblo.com)Below is the config.>>access-list inside_a...
Hi All,in my NEW network there are 6 VOIP PHONE Linksys SPA922. They are connected to an external VOIP PBX through internet, NO VPN has been setup.My firewall is a Cisco ASA 5505 with plus security licence installed. My firewall has a pubblic IP addr...
