Hello,I would like to know if it's possible to create a FWSM failover group compose of 3 FWSM nodes (one primary and two secondaries) as it can be done with an HSRP or VRRP group.Thanks.Serge.
Hello,I would like to know if it's possible to create a FWSM failover group compose of 3 FWSM nodes (one primary and two secondaries) as it can be done with an HSRP or VRRP group.Thanks.Serge.
Dear friends,I am getting the following message on FWSM:%FWSM-6-110001: No route to ff02::2 from fe80::217:f2ff:fe01:5bd0 In fact i am getting this message a huge number of times with the source and destination varying.But i am looking for a IPv4 for...
Greetings All,A while back I stumbled on podcast that gives details on you can use IP SLA to provide some sort of a failover. Now is the time that I'm actually needing to use it.Basically the goal is simple, I have one Firewall (ASA 5505) connected t...
Hi all, I have a question that I'd like you all to see if i"m going about this correctly. First I'll describe the topology, where I am now, then what i'm trying to achieve. Currently: 2 sites ( A. (small office) and B. (collocation cabinet at data ...
i have NAC 4.7.1 deployed as L3 OOB ,the problem is when you open the reports tab you should find red flags , and green flags , the red shows the users that is not compliant with the NAC requirements , the green shows the users that are compliant an...
Question from a Facebook reader : Is it best practice to connect the LAN failover through a switch or over a crossover cable?
Hi,i'm configuring a ASA 5510, i've the following partial configurationinterface ethernet 0/1 nameif Outside_net2 security-level 0 ip address 10.0.2.2 255.255.255.0!interface Ethernet0/3 nameif Inside_vlans security-level 100 ip address 192.168.10....
Hi all,I am looking to upgrade my ASA 5510 cluster to the latest code 8.3.1 from 8.0.5. Has anyone expreienced any undocumented issues with ASA version 8.3.1 ED?I'd like to get some real world feedback before I proceed.Thanks.
Hi,my inside interface user can't ping outside interface even after i have configured acl which allow ping and also icmp response, configured icmp inspection also.find below configuration of pix 515E which is running ios version 8.0(3)PIX Version 8.0...
How to change password on ASA5510. Thanks..
I have an unusual problem where ESMTP is working to some but not other Message Labs servers.I see this error on the ASA - ESMTP Classification: Dropped connection for ESMTP Request from inside:Questions is - do I need ESMTP inspect on the firewall?I ...
Hi allCan anyone tell me how fast the cisco asa can be configured to failover automatically?and also, If I type in no failover active on the primary, how fast will it failover?cheersCarl
Hi, Im having a weird case with my fwsm. There were times when the untrust interface suddenly drops all trafic, but after a few minutes it comes back again. I've already check the the np blocks, and it does not increment, thus proving that there ...
Hi,i have a 5510 and the asdm was working fine all the time. But the there was a power outage and ups ran out etc. On boot, internet works but asdm cannot be accessed and also remote access vpn does not work anymore. When i cli to it , i see all the ...
Hi folks,i have this estranged situation: I have two ASA's 5520 in Active/Standby failover mode. After the software update from 8.2(1) to 8.2(2) one of NAT(PAT) rules in outside interface unexpectedly disappeared from startup configuration/running co...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-26-2024 02:14 AM | ||
04-22-2024 06:41 AM | ||
04-21-2024 09:36 PM | ||
04-17-2024 12:36 PM | ||
04-17-2024 07:38 AM |
User | Count |
---|---|
10 | |
6 | |
4 | |
3 | |
3 |