HiIs it possible to configure the ASA Content Security and Control SSM module to filter URL's based on a username or group of users?Does the SSM have an LDAP connector?Thank you
HiIs it possible to configure the ASA Content Security and Control SSM module to filter URL's based on a username or group of users?Does the SSM have an LDAP connector?Thank you
hi,basically we are to perform a what its called double nat on our asa5510. on the outside int we have 10.1.1.0/24 network and on the inside int we have 10.1.200.0/24. so basically i figured out that we had to perform a double-nat for this scenario.c...
Hello,I have this configuration:Host 172.16.1.x/24 > ASA 5510 > Router 2811 > Router 871 > ASA 5505 > Host 172.16.2.x/ 24.I have add an FTP serve on port 2 of ASA 5510 with the ip address 172.16.0.2/252.I need to know how tho configure the access on ...
Hello,I have few servers placed on our DMZ, they all have static NAT, In order to access any port on the internet I need to put an ACL that allows traffic from DMZ to any. Shouldn't the DMZ by default be allowed to access the Internet, it is on highe...
What is the highest IPS 4240 engine that CSM will support? My IPS is presently at 6.01(E2)and CSM is 3.2.2. Can I upgrade to E3 and still have CSM manage the sensor?
just a quick question, What is the Hardware upgrade path for a PIX515. FYI Will not need IPsec, Thanks
I have configured some static translations for my new ASA 5510 which is on our new internet ciruit. For some reason, I see hits on my acl but get no response from internal hosts. I get hits on my inbound acl but still no response on the other end. ...
Hi all,So a couple of weeks ago I installed 64 bit Vista on all of my computers at the house.I was then asked to do some work from home and when I went to install the VPN client, I realized that 64 bit is not supported.I configured my ASA for Anyconn...
Hello,How can i configure the multiple context ASA with don't using the auto generated MAC address.I do not want to use 'MAC address auto"cmd.swami
We currently have a very basic hub and spoke setup with our ASA 5505s (8.04). Site A (192.168.60.x) has a two way tunnel with SiteB (10.10.50.x). Site C (192.168.40.x) has a two-way tunnel with SiteB (10.10.50.x). Traffic can get between A and B. Tra...
Two questions - 1) How or where do you setup the Mars 100E for NTP? Again, I see nothing in the GUI for this.2) I've got a report that emails me an Event type: TCP Segment Overwrite each morning. However, in the "host" column it always states "hostna...
We have a PIX 501 6.3(5) 50 user license that is rebooting itself several times per day, causing brief outages. Only 9 out of 50 licenses are in use, and memory use is about 75% (12385952/16777216). I've enabled debug logging to remote syslog, and al...
Hello, we would like to migrate our two failover PIX 525 with one 5580. because of less interfaces, i would like to know if ASA 5540 or 5580 supports to use all the interfaces with no need to dedicate interfaces to a network, at the moment PIX 525 ha...
any one knows which is the limit to filter URI by regex instances ??, the idea is filter content by match the http trafic and regex statements, this is going to be in a asa 5510
I have DMVPN network and no QoS.I want implement QoS in WAN network.I use cisco 28xx router with IOS c2800nm-advipservicesk9-mz.124-22.T.bin - on Tunnel interface no "service-policy output" command only on GigabitEthernet.This is my configuration:cla...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-26-2024 02:14 AM | ||
04-22-2024 06:41 AM | ||
04-21-2024 09:36 PM | ||
04-17-2024 12:36 PM | ||
04-17-2024 07:38 AM |
User | Count |
---|---|
10 | |
6 | |
4 | |
3 | |
3 |