Dear All,i am looking for a command which can tell me all the ifindex assigned to interface in router. i know that there is one command in catos show ifindex but i couldn't find the similar command in router.please help.thanks
Dear All,i am looking for a command which can tell me all the ifindex assigned to interface in router. i know that there is one command in catos show ifindex but i couldn't find the similar command in router.please help.thanks
HelloWe are migrating an ASA 5540 (8.0.4) to Firepower (6.2.3.10) and an ACL on ASA has the next sentence... access-list Outside extended permit ip object-group DM_INLINE_NETWORK_7 host Public-IP object-group network DM_INLINE_NETWORK_7network-object...
how can I set the timezone in firepower CLI (in the prompt ">") when I finished install the firepower pkg file ?
We have deployed two FMC 2500s in HA pair. Currently, it is sitting in the same rack, but I want to move the standby FMC to a different data center. I checked the document but didn't find any information about distance limitation between active and s...
Hi,i am a newbie in ASA so please bear with me,I have configured a site to site VPN between 2 sites. Site A can see Site B resourcesSite B can see Site A resources How can i transfer selected internet traffic from Site B to Site A? I am using ASDM b...
Hi All, We have build tunnel to HQ and branch, only some segment on HQ is unable to access application at branch office, but ping is able to ping.ASA model & version : 5516-X & 9.12(2) When HQ access to branch our asa get below message.the asa discar...
Hello All, I have 3 interfaces: outside, inside0, inside1. both inside interfaces routes to outside correctly. I have user A in inside0 and DVR in inside1. I need to allow user A to access DVR in inside1 port 80 inside0 = security-level 80inside1 = s...
I am having to find the Public IP of an Internal Server. This is a new server that we just integrated in the last few days. I have the VLAN IP and have already created the NAT object, but need to know how to assign a Public IP. Thanks!
Hello.If I have enabled http server on outside for AnyConnect page, and want to enable REST API plugin, how I can restrict REST request only on inside interface?Thank You
I am not able to find any documentation that says 6.7 it's either supported or not supported. I can only assume 6.5 is the latest version for NGFWv but I need to confirm this.6.7 was released by VMware last year I wonder if there is even something on...
just to double check my understanding of rules and inspection , when i create a rule from inside to outside any any for a user , if the user is browsing the net he will be able to get data back from the internet because http and https inspection is e...
i need to move a asa configuration into fmc but the problem is i cant figure out how to move the existing service policy and inspection rules into the new fmc? especially the inspection rules?
Hi Teck Guys. Please share a cisco validate design for putting FPS 2130 or Router ASR1K on edge. i have attached my block diagram. suggest the validate design. Thanks All.
Hi,I am login to the asa from a terminal server . After that I want to login to IPS session 1from that ips session how can I exit to asa from then to terminal server and finally exit from terminal server . Please help
Hi,Card Type: ASA_5500_Series_Security_Services_Module-10Model: ASA-SSM-10 App. name: IPSApp. Status: UpApp. Status Desc: App. version: 6.2(1)E3Data Plane Status: UpASA version 5520 I cannot connect to ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-26-2024 02:14 AM | ||
04-22-2024 06:41 AM | ||
04-21-2024 09:36 PM | ||
04-17-2024 12:36 PM | ||
04-17-2024 07:38 AM |
User | Count |
---|---|
10 | |
6 | |
4 | |
3 | |
3 |