user MWI lights indicating new VM. When calling into Unity - Unity indicates no new messages. Unity shows MWI should be lighted. Deleted VM box and recreated. Same issue. Is there a way to use Outlook Web Access to look inside the mailbox? Or b...
user MWI lights indicating new VM. When calling into Unity - Unity indicates no new messages. Unity shows MWI should be lighted. Deleted VM box and recreated. Same issue. Is there a way to use Outlook Web Access to look inside the mailbox? Or b...
Has anyone set up a FAX scenario where you have Did's over PRI coming in through a 2610 H323 w/ Call Manager? Will this work? I have an idea how i would do it, but i am not sure if it will work.Fax inbound--> Call Manager DN w/ Fwd all to Unity Pil...
Hi all I have a cisco router 1600 series with the following config.Can QoS be implemented on the serial 0 under the following configuration for VoIP traffic?? (IOS 11.3) If it is possible which one could be implemented LLQ or IP RTP??Thanks in advan...
i want to use compressed RTP G.729 stream between ip phones.Where can i turn it on on CCM 3.13a?Thanks, Martin
Hey all, I just built a Unity 3.1 box on a Cisco MCS platform. Call Manager version is 3.2. The Unity box was built using the platform config. disks included with the server.The build went fine, Unity services start normally. I then install the TSP (...
HI, I have 2 simple questions. Does Ata 186 work with Clarent gatekeeper ?If doesn´t , I have the option of buying a cisco 2600, What hardware/software requiremtns should I buy ?Regards
Hi there folksI was just wondering if the following was possible? We will have 2 CallManagers in the central site. In a remote site we will have a Catalyst 6000 with the E1 voice services module (WS-X6608-E1) installed. This module will be used for i...
In version 3.1 of Unity ... Am I correct? 1 Unity Server per Exchange 5.5 site? Yes, I know that this changes with Exchange 2000 ... but for this questions I am only concerned with Exchange 5.5.
Can Softphone be used with extension mobility. I have tried to configure it and cannot seem to get Softphone to recognise any lines.Thanks
In an AVVID set-up with VG200 MGCP gateway as PSTN back-up,is therea specific way of setting an external phone number mask for this gateway on the CallManager by which caller ID can be sent to the person receiving our call.Or must this be configured ...
I'm building Unity 3.1(1) using Exchange 5.5 as a remote message store.the remote message store is Ex5.5 running on an NT4 PDC.Unity has Exchange 5.5 management software which connects to the remote server OK.I can browse from the unity server to the...
How can i play divx file over the IpTv network?Need i codec or something?thx
How can we check the voice call bandwidth for VOIP in CISCO router using show command.
If user have second line on his IP phone, how can I assure the message left on it is actually going to his mailnbox?
We have a Unity 3.14 installation. The customer wants the ability to utilize the user option to forward calls to another location. However we can not get this option to work. So when they call into their extension and choose option 4, 1,2 the syst...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-22-2024 04:46 AM | ||
04-18-2024 07:46 AM | ||
04-15-2024 07:41 PM | ||
04-09-2024 02:09 PM | ||
02-25-2024 06:28 AM |