Other Collaboration Subjects

Hi all,we have callmanager to make low cost international calls.We have 3 carriers.we have setup route list for these carriers.one carrier don't have x destwe need but all others as well and best price so i setup him first.two others have all dest an...

We are having a problem with one MeetMe directory number. Here is our configuration: We are running a CCM 3.12(c) cluster, we have 3 MeetMe directory numbers 560-562, all conferencing and transcoding resources are being passed off to DSP's on a WS46...

I have a T1 CAS in a Catalyst 4224 as an H.323 Gateway to CM 3.2. Provider sends ANI in the form of *ANI*DNIS* using their E&M Wink Signalling. I have been told told that Cisco does not support ANI with their version of E&M Wink. My provider is not a...

Hi ALL !!!We have MIND iPhonex 3.10.042.4Real-time server in main window display thatgateway AS5350 connected, but over minute disconnected.And in Status bar: Failed to parsed UDP message from 1.1.1.3 at (time)My config is following below:! aaa group...

I have a 2 x 3640 routing data/voice the problem is when the pabx fails (power, or removal of utp to e1 card) then the router stops routing data for approx 20 seconds timing all workstation out.please helpregardsDon

Hi,We have an installation here of around 60 IP phones and we are connected to the PSTN using a VG200 with a PRI in h.323 mode. The users recieve an echo in the first 5-10 seconds of all their calls out through the gateway. Is this an experience tha...

I lost my Publisher today and also the CCM database. Fortunately this is a test box. I still can find the database (the last one used ) CCM0307 sitting in the Subscriber. Is there a way I can rename the Subscriber to become the Publisher and if not c...

I have Auto Attendant configured and when I call the route point number from an IP phone all works fine. If I call from PSTN to the GW running MGCP with the Attendant DN set to the route point number, the GW answers and I get nothing. Watching with ...

I am trying to identify new features that will be part of 3.3 or what ever the next major release of CallManager may be. Anyone have knowledge?I am focusing on finding out when hunt-groups will be supported and any other traditional PBX features.Than...

One other issue I noticed - and certianly tell me if this is just a problem in our Exchange 2000 deployment - but after I creat an internet-Only subscriber in the SA - it works fine - yeah!<br><br>But if I go back and try to change the address and sa...

We recorded a bunch of call handler greetings today. They all ended up having crackling noises. I have a tac case open to resolve this. I was hoping to be able to edit those greetings with an audio application to clean them up and remove those noises...

Yeah me again :-) In the process of solving my earlier issues (thanks by the way - making headway...I ran into a possible issue with our install:<br><br>I had mentioned we seemed to have twin copies of the AllSubscribers, etc. groups - only one of w...

The exchange administrator rebuilt the exchange server that Unity was registered to. This was on 3.0 Unity. This of course stopped Unity from working. A TAC case was opened, and they tried to edit registry to restore this connection. They were un...

Ok, new install, Unity 3.1.3 and CCM 3.1.3a ... TSP 6.0.2 loaded and tested (rebooted Unity twice as per earlier mention by Keith, JIC) ... 16 voice-ports, all added to the AllPartitions CCS (we have three Partitions, 3 site Centralized design) and a...

I have a user who is the primary owner of several exhanges mailboxes and those are assigned in unity.<br>When he access the ActiveAssistant Web Page, he gets<br>"<br>Your Windows Domain Account [EPIPHANY\jdoe] is associated with multiple Unity Subscr...