Anyone know of Cisco partners that do more for Historical Reporting on the IP ICD product ? Any URLs, etc.So far I only found one after searching;www.isi-info.com
Anyone know of Cisco partners that do more for Historical Reporting on the IP ICD product ? Any URLs, etc.So far I only found one after searching;www.isi-info.com
Greetings-Unity 3.0 Install with Exchange 2000. Symptom: can leave voice mail messages for users but can't retrieve the voice mail messages. In fact, after leaving a voice mail for a user, the user accesses unity and is told that there are no new me...
I have a few questions about Unity 3.0x?<br><br>I have unity 3.03 running as a member server in the AD with Exchange2K. There are 9 other exchange servers running 5.5 and Exchange2k. Some subscribers have Exchange2K mailstores, some 5.5, and some o...
Hi there,<br><br>A customer of mine pointed out a certain issue to me. When creating his situation on my demo-system I noticed the same problem. Both me and my customer use Unity 3.02 and Callmanager 3.11.<br><br>Situation:<br>4200 is used as a CTI r...
Do I have to reinstall Unity if I change the Exchange Service acount?<br><br>
upgrading Unity 2.46 to 3.x <br>(little bit of Callmanager [3.12C] too)<br><br>Callmanagers are in own workgroup (2 - pub and sub)<br>Unity in it's own domain w/ RT ver Exch 5.5 on the Unity box (voicemail only for now)<br>corp Lan in it's own domain...
We installed Unity 3.0 the port seems to be working fine. Added new subscriber and ext to Unity. When we press message on the IP Phone, it prompts us to enter user ID. At that point no matters what we enter we get invalid user ID.<br>We tried changin...
In a School environment, how can a parent call in and leave a VM with a teacher and then dial another ext and leave another VM with another teacher without having to dial the main 7 dig # again? Subscribers are setup to say goodbye after someone lea...
I want to connect a PABX with an E1 card set up for CAS signaling to a public (actually GSM) ISDN switch that does not support CAS. Is it possible to use a Cisco router with 2 E1 interfaces to do the conversion?
Is there anybody who succesfully configuredNetmeeting v.2.11 in CCM 3.1(2C) enviroments.Could you send me a link?Thank you
I am running Unity 3.0(2), with Exchange 5.5 installed on an NT 4.0 box. When I try to add an existing exchange subscriber, when I search for a user, I get two runtime errors: line 1045, expected ';' and line 2632, object expected. I can add a new ...
I have 2 installed locations on the latest version of Call Manager (3.1.2C) and current firmware loads that both have had Static and very loud hum coming in on ISDN PRI's attached to the 6608 blade of a 6500. Has anyone else experienced this. If yo...
Any voip expert can assist me ! I have a customer who want to implement the E1 (30 voip channels)module connecting to PBX that request for the redundancy when the primary E1 module failure. Typically, there are two chassis of Cisco 3662 with all the ...
I have two sites that want to run VOIP. Main site is a 2610 with a FXO card, the remote site is a 1751 with a FXO card. Each location has a PBX( key system). The question I have will this work and what kind of configuration I need to site-up. Also ea...
I want to configure an AS5300 with H323 Slow connect.I've tried with the configuretion that I found at cisco.com, but may be it is lacking something else. The gateway is using H323 fast connect.call rsvp-sync!interface fastethernet0...ip rsvp bandwid...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-22-2024 04:46 AM | ||
04-18-2024 07:46 AM | ||
04-15-2024 07:41 PM | ||
04-09-2024 02:09 PM | ||
02-25-2024 06:28 AM |