Hi,I have the following situation, If Phone A is in a Call with Phone B, Phone C is ringing and Phone A put B on Hold. If Phone A press GPickup to capture call on Phone C, it does not work. Anyone knows if it is by design?.thanks
Hi,I have the following situation, If Phone A is in a Call with Phone B, Phone C is ringing and Phone A put B on Hold. If Phone A press GPickup to capture call on Phone C, it does not work. Anyone knows if it is by design?.thanks
IP phones auto register with CM, and then use TAPS to overwrite this phone number. But I found this phone number will not be released after use TAPS. Any suggestions?
Using CM 4.1(3)SR1RTMT was running many times before.Now the application starts, ask for password and does not connect anymore.The configured alarms will be generated.many thanks in advanceThe restarting of the RIS service does not solve the problemR...
Dear Sir, Can the CallManager (ver 3.3(4) be installed on HP DL 385(AMD Opteron processor) server ?In the future, we are planning upgrade to CCM version 4.1(x) on the same server, can this be done? Please advise . Thank you very much.Regards
On CCM4.0(1) I'm configuring IPMA in shared mode. When I configure the manager, I can select 'mobile manager' to enable the manager to use extension mobility. However, I can't configure the assistant unless they have a hardphone as an associated devi...
I have a CME with running on a 3725 and iave some FXO' ports running on 2651 how is the best way to get the calls from the PSTN to route to the IP phones, DOes anyone have an sample config where the PSTN gateway is running on another router than the ...
We are running CCM v4.1(3)SR1 and PSTN voice gateway is using Cisco 3845. Does MGCP support on VIC-4FXS/DID and VIC-4FXO on Cisco 3845? Any CCO urls for reference will be helpful. Thanks.
Hi,On CCM Express, features for paging to IP Phone already include and it work ...does anybody have idea how to enable this feature on CCM Enterprise without third party software (ie :Berbee InformaCast), i'm using CCM 3.3(3).Many thank in advanced..
Have a small (5 set) CME site that will need to use the corp unioty server at HQ for vxmail.Will use PSTN for this. There is a small 56k frame data wan.How can we do this?PSTN for all calls is ok until the WAN gets upgrade next year, but how can we g...
I have just setup a brand new VG (2811) for a customer with 3 x E1s. The first 2 x E1s works fine, but when i tried to add the 3rd E1 onto the 2811, i get the following error:NSY-GW(config)#controller e1 0/1/1 NSY-GW(config-controller)#pri-...
HiCan any one give me a link with adequate info on the cisco EGW2200. I cant find a lot of info on this device.Thanks
Can anyone give me what the number pad reload sequence is on 7900 series phone under CCM 4.1? I remember it was **##**# for CCM 3.3
I have a 6500 with a CMM blade in it is running 12.3(8)XY5The CCM is 4.0(2a)sr2bThe PRI interfaces are up and registered just fine and working.It has a mediacard 4 that is configured totally for conferencing, however I could not get it to register wi...
We have some 7940 with SIP 3.0. First, we can not unlock the configuration because it is password set, and we do not know what the password is. We were hoping to re-set configuration so we could as well erase the configuration under Network settings....
When reception receives an external call and forwards this call to an internal number;1. After the ring timeout the external caller receives a message that there is no mailbox associated with the internal number.2. This also happens if the internal n...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-22-2024 04:46 AM | ||
04-18-2024 07:46 AM | ||
04-15-2024 07:41 PM | ||
04-09-2024 02:09 PM | ||
02-25-2024 06:28 AM |