cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
764
Views
5
Helpful
2
Replies

2821 voice gateway and NEC PABX with CAS Signalling

paulhardy
Level 1
Level 1

Hi

I ma implementing new system running call manager 4.1.3. the voice gateway is a cisco 2821 with NM-1CE1T1-PRI module installed. I got to get this communicating with a NEC PABX. The NEC engineer says he can configure the NEC E1 line for G703 CAS signalling. I need assistance on the config for the voice gateway to get it working.

Thanks

Paul

2 Replies 2

Here is a copy of the config I am using. I have used a H323 gateway . I am going to try the link that you send with the MGCP gateway and will let you know.

Building configuration...

Current configuration : 2368 bytes

!

version 12.3

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname pabxavr1

!

boot-start-marker

boot-end-marker

!

card type e1 1

logging buffered 4096 debugging

enable secret xxx

!

network-clock-participate wic 0

no aaa new-model

ip subnet-zero

!

!

ip cef

!

!

no ip domain lookup

ip host EUPHONIA 149.x.126.10

no ftp-server write-enable

isdn switch-type primary-net5

!

voice-card 0

dspfarm

dsp services dspfarm

!

!

!

voice service voip

fax protocol pass-through g711ulaw

modem passthrough nse codec g711ulaw

!

!

voice class codec 1000

codec preference 1 g711ulaw

!

!

!

voice class h323 1

h225 timeout tcp establish 5

!

!

!

!

!

!

!

!

!

!

!

controller E1 0/0/0

ds0-group 0 timeslots 1-15,17-31 type r2-digital dtmf dnis

!

controller E1 0/0/1

!

controller E1 1/0

!

!

!

interface Loopback0

ip address 129.94.x.x.255.255.255

!

interface GigabitEthernet0/0

ip address 129.94.x.x.255.255.252

duplex auto

speed auto

!

interface GigabitEthernet0/1

ip address 149.171.x.x.255.255.192

duplex auto

speed auto

!

router ospf 1000

log-adjacency-changes

auto-cost reference-bandwidth 1000

passive-interface default

no passive-interface GigabitEthernet0/0

network 129.94.x.x.0.0.0 area 0

network 129.94.x.x0.0.0.0 area 0

network 149.171.x.x.0.0.0 area 0

!

ip classless

!

!

ip http server

no ip http secure-server

!

!

!

!

control-plane

!

!

!

voice-port 0/0/0:0

!

!

!

!

dial-peer voice 1 pots

tone ringback alert-no-PI

description Outgoing Calls to NEC PABX

destination-pattern .T

progress_ind alert enable 8

direct-inward-dial

port 0/0/0:0

forward-digits 0

!

dial-peer voice 2 voip

description Inbound to CCM

destination-pattern 8....

progress_ind setup enable 3

modem passthrough nse codec g711ulaw

voice-class codec 1000

voice-class h323 1

session target dns:EUPHONIA

dtmf-relay h245-alphanumeric

fax-relay ecm disable

no vad

!

dial-peer voice 3 voip

description UCW 75XX DDI Range

destination-pattern 5....

modem passthrough nse codec g711ulaw

voice-class codec 1000

voice-class h323 1

session target dns:EUPHONIA

incoming called-number 8....

dtmf-relay h245-alphanumeric

fax-relay ecm disable

no vad

!

!

!

line con 0

line aux 0

line vty 0 4

password xxx

login

!

scheduler allocate 20000 1000

!

end

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: