Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

8.0(3) Phone Loads & Callmanager 4.1(3)

I am hearing mixed messages on support of the 7941/7961 8.0(3) Phone Loads (cmterm-7941_7961-sccp.8-0-3.exe). Documentation says it's supported only in 4.2, however I've heard they'll work in Callmanager 4.1(3)SR2. Can anyone confirm this?

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Red

Re: 8.0(3) Phone Loads & Callmanager 4.1(3)

Hi Brian,

The 8.0(3) firmware is supported on 4.1.3sr1 but there are some new features that require 4.2 or later for the CCM version. Have a look;

Cisco Unified IP Phone 7961G, 7961G-GE, 7941G, and 7941G-GE Release Notes for Firmware Release 8.0(3) for Cisco Unified CallManager 5.0, 4.2, 4.1, 4.0, and 3.3 (SCCP)

From this doc;

http://www.cisco.com/en/US/products/hw/phones/ps379/prod_release_note09186a008068f380.html#wp38956

Firmware Versions 8.0(3) for Cisco IP Phone Models 7941G and 7961G

The 8.0(3) firmware image within the installation program, supports the Skinny Client Control Protocol (SCCP) for the following Cisco IP Phone models:

Cisco IP Phone 7941G

Cisco IP Phone 7961G

This firmware version is supported on Cisco Unified CallManager Release 5.0 and higher, and Cisco Unified CallManager Releases 4.2, 4.1, 4.0, and 3.3.

Call Manager Version

4.1(3)SR1 or later & ciscocm.4-1-DevPack-23.exe

From the read-me doc;

http://ftp-sj.cisco.com/cisco/voice/ip-7900ser/cmterm-7941_7961-sccp.8-0-3-readme.htm

Hope this helps!

Rob

Please remember to rate helpful posts.........

1 REPLY
Hall of Fame Super Red

Re: 8.0(3) Phone Loads & Callmanager 4.1(3)

Hi Brian,

The 8.0(3) firmware is supported on 4.1.3sr1 but there are some new features that require 4.2 or later for the CCM version. Have a look;

Cisco Unified IP Phone 7961G, 7961G-GE, 7941G, and 7941G-GE Release Notes for Firmware Release 8.0(3) for Cisco Unified CallManager 5.0, 4.2, 4.1, 4.0, and 3.3 (SCCP)

From this doc;

http://www.cisco.com/en/US/products/hw/phones/ps379/prod_release_note09186a008068f380.html#wp38956

Firmware Versions 8.0(3) for Cisco IP Phone Models 7941G and 7961G

The 8.0(3) firmware image within the installation program, supports the Skinny Client Control Protocol (SCCP) for the following Cisco IP Phone models:

Cisco IP Phone 7941G

Cisco IP Phone 7961G

This firmware version is supported on Cisco Unified CallManager Release 5.0 and higher, and Cisco Unified CallManager Releases 4.2, 4.1, 4.0, and 3.3.

Call Manager Version

4.1(3)SR1 or later & ciscocm.4-1-DevPack-23.exe

From the read-me doc;

http://ftp-sj.cisco.com/cisco/voice/ip-7900ser/cmterm-7941_7961-sccp.8-0-3-readme.htm

Hope this helps!

Rob

Please remember to rate helpful posts.........

251
Views
0
Helpful
1
Replies
CreatePlease to create content