04-27-2003 11:30 PM - edited 03-12-2019 11:37 PM
Hi all!
On a 2651XM with 2 BRI port, we recognize a strange problem. Direct inward dialing is ok, let's say on phone 2105. If I redirect a phone in the PSTN to 2105 (redirected by provider network), the provider network sends a additional information with the call, so the call will fail with the ISDN debug message "ISDN ERROR unsupported bearer cap".
Does anybody know about that problem?
Thanks, Andy
04-28-2003 07:44 PM
We need to see what are that additional information which comes with the isdn SETUP message for a forwarded call which is not received in the regualr dialin call.
So pl. enable the "debug isdn q931" and make a call directly from pstn to that 2105 AND also capture the same for a call forwarded to that 2105. Post both the isdn debug here so that we can compare.
04-28-2003 10:39 PM
Thanks for the reply. Here a quick describtion of th e situation:
First Call to phone "22" from "0794060041" (calling id is not visible because it is anonymous!) is ok. Then I redirect the phone "0794060041" to "22" and call it from another phone, the call fails. Below you can find thew debuging of this behaviour:
voicegate01#
Apr 29 08:35:42.683: ISDN BR1/1 Q931: RX <- SETUP pd = 8 callref = 0x01
Sending Complete
Bearer Capability i = 0x8090A3
Standard = CCITT
Transer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0x89
Calling Party Number i = 0x00A3
Plan:Unknown, Type:Unknown
Called Party Number i = 0x81, '22'
Plan:ISDN, Type:Unknown
Apr 29 08:35:42.703: ISDN BR1/1 Q931: TX -> CALL_PROC pd = 8 callref = 0x81
Channel ID i = 0x89
Apr 29 08:35:42.731: ISDN BR1/1 Q931: TX -> ALERTING pd = 8 callref = 0x81
Apr 29 08:35:50.479: ISDN BR1/1 Q931: RX <- DISCONNECT pd = 8 callref = 0x01
Cause i = 0x8090 - Normal call clearing
Apr 29 08:35:50.483: ISDN BR1/1 Q931: TX -> RELEASE pd = 8 callref = 0x81
Cause i = 0x8090 - Normal call clearing
Apr 29 08:35:50.567: ISDN BR1/1 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x01
voicegate01#
voicegate01#
voicegate01#
Apr 29 08:36:30.071: ISDN BR1/1 Q931: RX <- SETUP pd = 8 callref = 0x01
Sending Complete
Bearer Capability i = 0x8090A3
Standard = CCITT
Transer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0x89
Facility i = 0x91A1130202152602010F300A0201010A0101A1028100
- ETSI Supplementary Service, Invoke, Diverting leg 2
Progress Ind i = 0x8583 - Origination address is non-ISDN
Calling Party Number i = 0x0181, '0313840511'
Plan:ISDN, Type:Unknown
Called Party Number i = 0x81, '22'
Plan:ISDN, Type:Unknown
Apr 29 08:36:30.075: ISDN BR1/1 **ERROR**: host_incoming_call: Received a call with a bad bearer cap from
1
Apr 29 08:36:34.067: ISDN BR1/1 Q931: RX <- SETUP pd = 8 callref = 0x01
Sending Complete
Bearer Capability i = 0x8090A3
Standard = CCITT
Transer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0x89
Facility i = 0x91A1130202152602010F300A0201010A0101A1028100
- ETSI Supplementary Service, Invoke, Diverting leg 2
Progress Ind i = 0x8583 - Origination address is non-ISDN
Calling Party Number i = 0x0181, '0313840511'
Plan:ISDN, Type:Unknown
Called Party Number i = 0x81, '22'
Plan:ISDN, Type:Unknown
Apr 29 08:36:34.075: ISDN BR1/1 **ERROR**: host_incoming_call: Received a call with a bad bearer cap from
1
Apr 29 08:36:38.067: ISDN BR1/1 Q931: RX <- DISCONNECT pd = 8 callref = 0x01
Cause i = 0x82E6 - Recovery on timer expiry
Apr 29 08:36:38.071: ISDN BR1/1 Q931: L3_Go: L3_GetUser_NLCB returned NULL cid 0x0 cr 0x81 ev 0x45 ces 1 -- Message igno
red
Apr 29 08:36:38.075: ISDN BR1/1 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x81
Cause i = 0x80D1 - Invalid call reference value
Thanks for your support!
Andy
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: