Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

call fails - no circuit (34)

Hi all,

.. call fails, as you can see, to exit through dial-peer 200 and so are switched to dial-peer 100 (the reason is there is no circuit). I think gatekeeper and dial-peer configuration is ok. Also on the remote side everything should be configured ok. What problem do you think can be? I'm really in trouble.

show dial-peer voice 200:

VoiceOverIpPeer200

peer type = voice, information type = voice,

description = `',

tag = 200, destination-pattern = `.T',

answer-address = `', preference=1,

CLID Restriction = None

CLID Network Number = `'

CLID Second Number sent

CLID Override RDNIS = disabled,

source carrier-id = `', target carrier-id = `',

source trunk-group-label = `', target trunk-group-label = `',

numbering Type = `unknown'

group = 200, Admin state is up, Operation state is up,

incoming called-number = `', connections/maximum = 0/unlimited,

DTMF Relay = disabled,

modem transport = system,

URI classes:

Incoming (Called) =

Incoming (Calling) =

Destination =

huntstop = disabled,

in bound application associated: 'DEFAULT'

out bound application associated: ''

dnis-map =

permission :both

incoming COR list:maximum capability

outgoing COR list:minimum requirement

Translation profile (Incoming):

Translation profile (Outgoing):

incoming call blocking:

translation-profile = `'

disconnect-cause = `no-service'

advertise 0x40 capacity_update_timer 25 addrFamily 4 oldAddrFamily 4

type = voip, session-target = `ras',

technology prefix: 70

settle-call = disabled

ip media DSCP = ef, ip signaling DSCP = af31,

ip video rsvp-none DSCP = af41,ip video rsvp-pass DSCP = af41

ip video rsvp-fail DSCP = af41,

UDP checksum = disabled,

session-protocol = cisco, session-transport = system,

req-qos = best-effort, acc-qos = best-effort,

req-qos video = best-effort, acc-qos video = best-effort,

req-qos audio def bandwidth = 64, req-qos audio max bandwidth = 0,

req-qos video def bandwidth = 384, req-qos video max bandwidth = 0,

RTP dynamic payload type values: NTE = 101

Cisco: NSE=100, fax=96, fax-ack=97, dtmf=121, fax-relay=122

CAS=123, ClearChan=125, PCM switch over u-law=0,A-law=8

RTP comfort noise payload type = 19

fax rate = voice, payload size = 20 bytes

fax protocol = system

fax-relay ecm enable

fax NSF = 0xAD0051 (default)

codec = transparent, payload size = 0 bytes,

Media Setting = flow-through (global)

Expect factor = 10, Icpif = 20,

Playout Mode is set to adaptive,

Initial 60 ms, Max 250 ms

Playout-delay Minimum mode is set to default, value 40 ms

Fax nominal 300 ms

Max Redirects = 1, signaling-type = cas,

VAD = enabled, Poor QOV Trap = disabled,

Source Interface = NONE

voice class sip url = system,

voice class sip rel1xx = system,

redirect ip2ip = disabled

probe disabled,

voice class perm tag = `'

Time elapsed since last clearing of voice call statistics never

Connect Time = 0, Charged Units = 0,

Successful Calls = 0, Failed Calls = 1144, Incomplete Calls = 0

Accepted Calls = 0, Refused Calls = 0,

Last Disconnect Cause is "22 ",

Last Disconnect Text is "no circuit (34)",

Last Setup Time = 300456456

  • Other Collaboration Voice and Video Subjects
1 REPLY
New Member

Re: call fails - no circuit (34)

gatekeeper and dial-peers configuration:

gatekeeper

zone local localGKname localdomain localGKIP

zone remote remoteGk1name remoteGK1domain remoteGK1IP 1719

zone remote remoteGK2name remoteGK2domain remoteGK2IP 1719

zone remote remoteGk3name remoteGK3domain remoteGK3IP 1719

zone subnet localGKname ...IP.../19 enable

zone prefix Gk1 50*

zone prefix Gk2 70*

zone prefix Gk3 70*

no shutdown

server registration-port 1718

dial-peer voice 100 voip

preference 10

destination-pattern .T

session target ras

tech-prefix 50

codec transparent

dial-peer voice 200 voip

destination-pattern .T

session target ras

tech-prefix 70

codec transparent

1232
Views
0
Helpful
1
Replies
This widget could not be displayed.