Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Called ID for incoming call

I have call manager 3.2 and cisco 2650 router. I want to see the incoming number on my IP phone. Is there any way in call manager 3.2?

15 REPLIES
Bronze

Re: Called ID for incoming call

You can set in the gateway settings on call manager:

Calling Party Selection* Originator

Presentation Bit* Allowed

Display IE Delivery (checked)

Geoff

New Member

Re: Called ID for incoming call

Thanks for the reply. I did but still it is shwoing unknown caller ID. By the way the call is routed through UNity. Callcomes in and than unity attendent route the call. Is any parameter on the unity to be defined.

New Member

Re: Called ID for incoming call

Hi,

Here are some questions to guide in the right direction:

1.Does the interface that connects to the PSTN supports passing caller ID information.

2. Does the voice signalling protocol support passing caller ID? (for example, MGCP on an FXO interface might not support passing the Caller ID information)

3. Is the carrier sending Caller ID information in the first place? Running debugs such as 'debug voip ccapi inout' or 'debug isdn q931' might help here.

Good luck.

New Member

Re: Called ID for incoming call

I have FXO card into 2650 router.and i have h323 gateway configured on the call manger.I checked with phone compnay and they are passing the caller id information. How will I know that interface supports the caller id or not.

New Member

Re: Called ID for incoming call

First verify that is is one of these:

VIC-2FXO-M1 or VIC-2FXO-M2

If it is, then turn on 'debug voip ccapi inout while placing an inbound call. Verify from the traces that the information is being passed.

Regards.

New Member

Re: Called ID for incoming call

It has VIC-2FXO-M1

New Member

Re: Called ID for incoming call

the output if the debug voip ccapi inout is :The incoming call was coming from 4807973688 and the number was dialed was 6024580400.

Can you find that is it problem with router or call manager

30w5d: ssaReportDigitsDone cid(23858) peer list: tag(1) called number (1000) tag(2) called number (1000) tag(3) called number (1000)

30w5d: ssaReportDigitsDone callid=23858 Reporting disabled.

30w5d: cc_api_call_proceeding(vdbPtr=0x82427750, callID=0x5D33,

prog_ind=0x0)

30w5d: cc_api_call_notify(vdbPtr=0x82427750, callID=0x5D33

30w5d: sess_appl: ev(21=CC_EV_CALL_PROCEEDING), cid(23859), disp(0)

30w5d: cid(23859)st(SSA_CS_CALL_SETTING)ev(SSA_EV_CALL_PROCEEDING)

oldst(SSA_CS_MAPPING)cfid(-1)csize(0)in(0)fDest(0)

30w5d: -cid2(23858)st2(SSA_CS_CALL_SETTING)oldst2(SSA_CS_CALL_SETTING)

30w5d: ssaCallProc

30w5d: ccGetDialpeerTag (callID=0x5D32)

30w5d: ssaIgnore cid(23859), st(SSA_CS_CALL_SETTING),oldst(1), ev(21)

30w5d: sess_appl: ev(20=CC_EV_CALL_NOTIFY), cid(23859), disp(0)

30w5d: cid(23859)st(SSA_CS_CALL_SETTING)ev(SSA_EV_CALL_NOTIFY)

oldst(SSA_CS_CALL_SETTING)cfid(-1)csize(0)in(0)fDest(0)

30w5d: -cid2(23858)st2(SSA_CS_CALL_SETTING)oldst2(SSA_CS_CALL_SETTING)

30w5d: ssaNotify

30w5d: ccCallNotify (callID=0x5D32)

30w5d: cc_api_call_alert(vdbPtr=0x82427750, callID=0x5D33, prog_ind=0x0, sig_ind=0x1)

30w5d: sess_appl: ev(7=CC_EV_CALL_ALERT), cid(23859), disp(0)

30w5d: cid(23859)st(SSA_CS_CALL_SETTING)ev(SSA_EV_CALL_ALERT)

oldst(SSA_CS_CALL_SETTING)cfid(-1)csize(0)in(0)fDest(0)

30w5d: -cid2(23858)st2(SSA_CS_CALL_SETTING)oldst2(SSA_CS_CALL_SETTING)

30w5d: ssaAlert

30w5d: ccGetDialpeerTag (callID=0x5D32)

30w5d: ccCallAlert (callID=0x5D32, prog_ind=0x0, sig_ind=0x1)

30w5d: cc_api_call_connected(vdbPtr=0x82427750, callID=0x5D33), prog_ind = 0cc_api_call_connected: setting callEntry->connected to TRUE

30w5d: sess_appl: ev(8=CC_EV_CALL_CONNECTED), cid(23859), disp(0)

30w5d: cid(23859)st(SSA_CS_ALERT_RCVD)ev(SSA_EV_CALL_CONNECTED)

oldst(SSA_CS_CALL_SETTING)cfid(-1)csize(0)in(0)fDest(0)

30w5d: -cid2(23858)st2(SSA_CS_ALERT_RCVD)oldst2(SSA_CS_CALL_SETTING)

30w5d: ssaConnect

30w5d: ccGetDialpeerTag (callID=0x5D32)

30w5d: ccConferenceCreate (confID=0x825032DC, callID1=0x5D32, callID2=0x5D33, tag=0x0)

30w5d: cc_api_bridge_done (confID=0x2DAC, srcIF=0x82427750, srcCallID=0x5D33, dstCallID=0x5D32, disposition=0, tag=0x0)

30w5d: cc_api_bridge_done (confID=0x2DAC, srcIF=0x82520DCC, srcCallID=0x5D32, dstCallID=0x5D33, disposition=0, tag=0x0)

30w5d: cc_api_caps_ind (dstVdbPtr=0x82427750, dstCallId=0x5D33, srcCallId=0x5D32,

caps={codec=0x2EBFB, fax_rate=0x7F, vad=0x3, modem=0x2

codec_bytes=0, signal_type=3})

30w5d: cc_api_caps_ind (Playout: mode 0, initial 60,min 40, max 200)

30w5d: cc_api_caps_ind (dstVdbPtr=0x82520DCC, dstCallId=0x5D32, srcCallId=0x5D33,

caps={codec=0x1, fax_rate=0x2, vad=0x1, modem=0x0

codec_bytes=160, signal_type=2})

30w5d: cc_api_caps_ind (Playout: mode 0, initial 60,min 40, max 200)

30w5d: cc_api_caps_ack (dstVdbPtr=0x82520DCC, dstCallId=0x5D32, srcCallId=0x5D33,

caps={codec=0x1, fax_rate=0x2, vad=0x1, modem=0x0

codec_bytes=160, signal_type=2, seq_num_start=1943})

30w5d: cc_api_caps_ack (dstVdbPtr=0x82427750, dstCallId=0x5D33, srcCallId=0x5D32,

caps={codec=0x1, fax_rate=0x2, vad=0x1, modem=0x0

codec_bytes=160, signal_type=2, seq_num_start=1943})

30w5d: cc_api_voice_mode_event , callID=0x5D32

30w5d: Call Pointer =8272E13C

30w5d: sess_appl: ev(29=CC_EV_CONF_CREATE_DONE), cid(23858), disp(0)

30w5d: cid(23858)st(SSA_CS_CONFERENCING)ev(SSA_EV_CONF_CREATE_DONE)

oldst(SSA_CS_CALL_SETTING)cfid(11692)csize(2)in(1)fDest(1)

30w5d: -cid2(23859)st2(SSA_CS_CONFERENCING)oldst2(SSA_CS_ALERT_RCVD)

30w5d: ssaConfCreateDone

30w5d: ccCallConnect (callID=0x5D32), prog_ind = 0ccCallConnect: setting callEntry->connected to TRUE

30w5d: ssaFlushPeerTagQueue cid(23858) peer list: tag(1) called number (1000) tag(2) called number (1000) tag(3) called number (1000)

30w5d: sess_appl: ev(51=CC_EV_VOICE_MODE_DONE), cid(23858), disp(0)

30w5d: cid(23858)st(SSA_CS_ACTIVE)ev(SSA_EV_VOICE_MODE_DONE)

oldst(SSA_CS_CONFERENCING)cfid(11692)csize(2)in(1)fDest(1)

30w5d: -cid2(23859)st2(SSA_CS_ACTIVE)oldst2(SSA_CS_ALERT_RCVD)

30w5d: ssaIgnore cid(23858), st(SSA_CS_ACTIVE),oldst(5), ev(51)

30w5d: cc_process_notify_bridge_done (event=0x824FB3A0)

30w5d: cc_api_call_digit_begin (dstVdbPtr=0x82427750, dstCallId=0x5D33, srcCallId=0x5D32,

digit=1, digit_begin_flags=0x1, rtp_timestamp=0xF60976EE

rtp_expiration=0x0, dest_mask=0x2)

30w5d: cc_api_call_digit_end (dstVdbPtr=0x82427750, dstCallId=0x5D33, srcCallId=0x5D32,

digit=1,duration=170,xruleCallingTag=0,xruleCalledTag=0, dest_mask=0x2), digit_tone_mode=0

30w5d: cc_api_call_digit_begin (dstVdbPtr=0x82427750, dstCallId=0x5D33, srcCallId=0x5D32,

digit=1, digit_begin_flags=0x1, rtp_timestamp=0xF609836E

rtp_expiration=0x0, dest_mask=0x2)

30w5d: cc_api_call_digit_end (dstVdbPtr=0x82427750, dstCallId=0x5D33, srcCallId=0x5D32,

digit=1,duration=210,xruleCallingTag=0,xruleCalledTag=0, dest_mask=0x2), digit_tone_mode=0

30w5d: cc_api_call_digit_begin (dstVdbPtr=0x82427750, dstCallId=0x5D33, srcCallId=0x5D32,

digit=0, digit_begin_flags=0x1, rtp_timestamp=0xF609A39E

rtp_expiration=0x0, dest_mask=0x2)

30w5d: cc_api_call_digit_end (dstVdbPtr=0x82427750, dstCallId=0x5D33, srcCallId=0x5D32,

digit=0,duration=190,xruleCallingTag=0,xruleCalledTag=0, dest_mask=0x2), digit_tone_mode=0

30w5d: cc_api_call_digit_begin (dstVdbPtr=0x82427750, dstCallId=0x5D33, srcCallId=0x5D32,

digit=4, digit_begin_flags=0x1, rtp_timestamp=0xF609B4F6

rtp_expiration=0x0, dest_mask=0x2)

30w5d: cc_api_call_digit_end (dstVdbPtr=0x82427750, dstCallId=0x5D33, srcCallId=0x5D32,

digit=4,duration=190,xruleCallingTag=0,xruleCalledTag=0, dest_mask=0x2), digit_tone_mode=0

30w5d: cc_api_call_userinfo(vdbPtr=0x82427750, callID=0x5D33

30w5d: sess_appl: ev(26=CC_EV_CALL_USERINFO), cid(23859), disp(0)

30w5d: cid(23859)st(SSA_CS_ACTIVE)ev(SSA_EV_CALL_USERINFO)

oldst(SSA_CS_ALERT_RCVD)cfid(11692)csize(2)in(0)fDest(0)

30w5d: -cid2(23858)st2(SSA_CS_ACTIVE)oldst2(SSA_CS_ACTIVE)

30w5d: ssaUserInfo

30w5d: ccGenerateTone (callID=0x5D32 tone=0)

30w5d: cc_api_call_userinfo(vdbPtr=0x82427750, callID=0x5D33

30w5d: sess_appl: ev(26=CC_EV_CALL_USERINFO), cid(23859), disp(0)

30w5d: cid(23859)st(SSA_CS_ACTIVE)ev(SSA_EV_CALL_USERINFO)

oldst(SSA_CS_ACTIVE)cfid(11692)csize(2)in(0)fDest(0)

30w5d: -cid2(23858)st2(SSA_CS_ACTIVE)oldst2(SSA_CS_ACTIVE)

30w5d: ssaUserInfo

30w5d: ccGenerateTone (callID=0x5D32 tone=1)

30w5d: cc_api_call_userinfo(vdbPtr=0x82427750, callID=0x5D33

30w5d: sess_appl: ev(26=CC_EV_CALL_USERINFO), cid(23859), disp(0)

30w5d: cid(23859)st(SSA_CS_ACTIVE)ev(SSA_EV_CALL_USERINFO)

oldst(SSA_CS_ACTIVE)cfid(11692)csize(2)in(0)fDest(0)

30w5d: -cid2(23858)st2(SSA_CS_ACTIVE)oldst2(SSA_CS_ACTIVE)

30w5d: ssaUserInfo

30w5d: ccGenerateTone (callID=0x5D32 tone=0)

30w5d: cc_api_call_disconnected(vdbPtr=0x82427750, callID=0x5D33, cause=0x3)

30w5d: sess_appl: ev(11=CC_EV_CALL_DISCONNECTED), cid(23859), disp(0)

30w5d: cid(23859)st(SSA_CS_ACTIVE)ev(SSA_EV_CALL_DISCONNECTED)

oldst(SSA_CS_ACTIVE)cfid(11692)csize(2)in(0)fDest(0)

30w5d: -cid2(23858)st2(SSA_CS_ACTIVE)oldst2(SSA_CS_ACTIVE)

30w5d: ssa: Disconnected cid(23859) state(5) cause(0x3)

30w5d: ccConferenceDestroy (confID=0x2DAC, tag=0x0)

30w5d: cc_api_bridge_drop_done (confID=0x2DAC, srcIF=0x82427750, srcCallID=0x5D33, dstCallID=0x5D32, disposition=0 tag=0x0)

30w5d: cc_api_bridge_drop_done (confID=0x2DAC, srcIF=0x82520DCC, srcCallID=0x5D32, dstCallID=0x5D33, disposition=0 tag=0x0)

30w5d: sess_appl: ev(30=CC_EV_CONF_DESTROY_DONE), cid(23858), disp(0)

30w5d: cid(23858)st(SSA_CS_CONF_DESTROYING)ev(SSA_EV_CONF_DESTROY_DONE)

oldst(SSA_CS_ACTIVE)cfid(11692)csize(2)in(1)fDest(1)

30w5d: -cid2(23859)st2(SSA_CS_CONF_DESTROYING)oldst2(SSA_CS_ACTIVE)

30w5d: ssaConfDestroyDone

30w5d: ccCallDisconnect (callID=0x5D32, cause=0x3 tag=0x0)

30w5d: ccCallDisconnect: existing_cause = 0x0, new_cause = 0x3

30w5d: ccCallDisconnect (callID=0x5D33, cause=0x3 tag=0x0)

30w5d: ccCallDisconnect: existing_cause = 0x0, new_cause = 0x3

30w5d: cc_api_call_disconnect_done(vdbPtr=0x82520DCC, callID=0x5D32, disp=0, tag=0x0)

30w5d: cc_api_icpif: expect factor = 0

30w5d: g113_calculate_impairment (delay=78,

loss=0), Io=0 Iq=0 Idte=0 Idd=0 Ie=0 Itot=0

30w5d: cc_api_call_disconnect_done(vdbPtr=0x82427750, callID=0x5D33, disp=0, tag=0x0)

30w5d: sess_appl: ev(12=CC_EV_CALL_DISCONNECT_DONE), cid(23858), disp(0)

30w5d: cid(23858)st(SSA_CS_DISCONNECTING)ev(SSA_EV_CALL_DISCONNECT_DONE)

oldst(SSA_CS_CONF_DESTROYING)cfid(-1)csize(2)in(1)fDest(1)

30w5d: -cid2(23859)st2(SSA_CS_DISCONNECTING)oldst2(SSA_CS_ACTIVE)

30w5d: ssaDisconnectDone

30w5d: sess_appl: ev(12=CC_EV_CALL_DISCONNECT_DONE), cid(23859), disp(0)

30w5d: cid(23859)st(SSA_CS_DISCONNECTING)ev(SSA_EV_CALL_DISCONNECT_DONE)

oldst(SSA_CS_ACTIVE)cfid(-1)csize(1)in(0)fDest(0)

30w5d: ssaDisconnect

New Member

Re: Called ID for incoming call

Hi Rakesh,

The debug output you posted captured the call while in the CALL PROCEEDING stage. The interesting portion would have been a little earlier, in the SETUP phase. Can you test and post again and include the initial phase of the call? Turn on 'service timestamps debug datetime msec' in configuration mode so that the debugs may be timestamped.

What does the config of the voice port look like here? Is the 'caller id enable' command present? See also:

http://www.cisco.com/en/US/products/sw/iosswrel/ps1834/products_feature_guide09186a008009cc4b.html#1050199

Regards,

Michael.

New Member

Re: Called ID for incoming call

You gave me the very good link but still the caller-id command is not supported on the router. I am running IOS version flash:c2600-jsx-mz.122-12.bin. THe caller id is supported 12.1(2)XH or 12.1(3)T. Idon't know why it is not showing in my IOS.

New Member

Re: Called ID for incoming call

So I understand that VIC-2FXO does not support caller id. Is it hardaware or software issue. Can we do something in order to VIC-FXO can support it ??

Thanks.

New Member

Re: Called ID for incoming call

It works i have a VIC-2FXO-M1 and I am able to see the incoming calling number. I have an h323 gateway.

New Member

Re: Called ID for incoming call

Somebody knows if I can upgrade/update VIC-FXO to VIC-FXOM2 ?

Does VIC-FXO support caller-id ??

Bronze

Re: Called ID for incoming call

Nope, you need the new hardware unfortunately.

Anonymous
N/A

Re: Called ID for incoming call

Hello all, do you know if FX0 ports in EM-HDA-4FXO card support caller id?, thanks

Anonymous
N/A

Re: Called ID for incoming call

I just found that EM-HDA-4FXO card support battery polarity reversal detection and Caller ID. Thanks anyway.

216
Views
0
Helpful
15
Replies