01-21-2003 08:49 PM - edited 03-12-2019 10:22 PM
I have a 3620 router, configured as SRST gateway. During SRST mode, I was unable to receive any call from PSTN, I have to dial the full digits to make PSTN call. i don't have the debug info now. Append is the configuration, what could have gone wrong:
!
clock timezone singapore 8
voice-card 1
!
ip subnet-zero
!
!
no ip domain-lookup
!
ip audit notify log
ip audit po max-events 100
!
class-map match-all voip-media
match access-group 100
class-map match-all voip-sig
match access-group 101
class-map match-all voipmedia
match ip dscp 46
class-map match-all voipsig
match ip dscp 26
!
!
policy-map wanqos
class voipmedia
priority 1000
class voipsig
bandwidth 200
class class-default
fair-queue
policy-map mark2zero
class class-default
set ip dscp 0
policy-map voip-qos
class voip-media
priority 1000
class voip-sig
bandwidth 200
class class-default
fair-queue
policy-map dscp2cos
class voipmedia
set cos 5
class voipsig
set cos 3
!
!
isdn switch-type basic-net3
!
voice rtp send-recv
!
voice class codec 100
codec preference 1 g711ulaw
!
!
!
voice class h323 10
h225 timeout tcp establish 3
!
!
!
!
fax interface-type fax-mail
mta receive maximum-recipients 0
!
controller E1 1/0
pri-group timeslots 1-31
!
translation-rule 389
Rule 1 638937.% 37 ANY abbreviated
!
translation-rule 9
Rule 0 ^.% 9
!
translation-rule 68266
Rule 0 ^682661.% 1
Rule 1 ^682662.% 2
Rule 2 ^682663.% 3
Rule 3 ^682665.% 5
!
!
!
!
interface BRI0/0
description Backup ISDN 64K for BMRC Leased
no ip address
encapsulation ppp
no ip route-cache
no ip mroute-cache
dialer pool-member 1
isdn switch-type basic-net3
no fair-queue
ppp authentication chap
!
interface Ethernet0/0
bandwidth 100
ip address 10.178.203.254 255.255.255.0
no ip route-cache
no ip mroute-cache
full-duplex
h323-gateway voip interface
h323-gateway voip bind srcaddr 10.178.203.254
!
interface Serial0/0
description 2048K Leased Line to Science Park
bandwidth 2048
backup delay 0 20
backup interface Dialer0
ip address 10.178.221.4 255.255.255.248
encapsulation ppp
no ip mroute-cache
service-policy output wanqos
!
interface Ethernet0/1
bandwidth 100
no ip address
no ip route-cache
no ip mroute-cache
shutdown
full-duplex
!
interface Serial1/0:15
no ip address
no ip route-cache
no logging event link-status
isdn switch-type primary-net5
isdn incoming-voice voice
isdn T309-enable
isdn send-alerting
isdn sending-complete
no cdp enable
!
interface Dialer0
ip address 10.178.221.3 255.255.255.248
ip access-group 102 in
encapsulation ppp
dialer pool 1
dialer idle-timeout 900
dialer string 68730244
dialer-group 1
ppp authentication chap
!
ip classless
ip route 0.0.0.0 0.0.0.0 10.178.221.1
ip route 10.178.192.0 255.255.255.0 10.178.221.1
ip route 10.178.196.0 255.255.255.0 10.178.221.1
ip route 10.178.204.0 255.255.255.0 10.178.221.1
no ip http server
no ip pim bidir-enable
!
!
logging history debugging
logging trap debugging
logging 10.178.203.1
access-list 100 permit udp any any range 16384 32767
access-list 100 permit udp any range 16384 32767 any
access-list 101 permit tcp any host 10.178.196.1
access-list 101 permit tcp host 10.178.196.1 any
access-list 101 permit tcp any host 10.178.196.2
access-list 101 permit tcp host 10.178.196.2 any
access-list 102 deny tcp any host 10.178.196.1
access-list 102 deny tcp host 10.178.196.1 any
access-list 102 deny tcp any host 10.178.196.2
access-list 102 deny tcp host 10.178.196.2 any
access-list 102 permit ip any any
dialer-list 1 protocol ip list 102
!
call rsvp-sync
!
voice-port 1/0:15
!
!
mgcp profile default
!
dial-peer cor custom
!
!
!
dial-peer voice 200 voip
incoming called-number .
destination-pattern 68266[1-3,5]..
progress_ind setup enable 3
translate-outgoing calling 9
translate-outgoing called 68266
voice-class codec 100
voice-class h323 10
session target ipv4:10.178.196.2
dtmf-relay h245-alphanumeric
ip qos dscp cs5 media
ip qos dscp cs3 signaling
no vad
!
dial-peer voice 100 pots
destination-pattern 9[6,9].......
progress_ind alert enable 8
direct-inward-dial
port 1/0:15
!
dial-peer voice 101 pots
destination-pattern 9018T
progress_ind alert enable 8
direct-inward-dial
port 1/0:15
prefix 018
!
dial-peer voice 102 pots
destination-pattern 9800T
progress_ind alert enable 8
direct-inward-dial
port 1/0:15
prefix 800
!
dial-peer voice 103 pots
destination-pattern 91800T
progress_ind alert enable 8
direct-inward-dial
port 1/0:15
prefix 1800
!
dial-peer voice 104 pots
destination-pattern 91900T
progress_ind alert enable 8
direct-inward-dial
port 1/0:15
prefix 1900
!
dial-peer voice 105 pots
destination-pattern 91...
progress_ind alert enable 8
direct-inward-dial
port 1/0:15
prefix 1
!
dial-peer voice 106 pots
destination-pattern 91..
progress_ind alert enable 8
direct-inward-dial
port 1/0:15
prefix 1
!
dial-peer voice 107 pots
destination-pattern 99..
progress_ind alert enable 8
direct-inward-dial
port 1/0:15
prefix 9
!
dial-peer voice 108 pots
destination-pattern 900T
progress_ind alert enable 8
direct-inward-dial
port 1/0:15
prefix 00
!
dial-peer voice 201 voip
incoming called-number .
destination-pattern 68266[1-3,5]..
progress_ind setup enable 3
translate-outgoing calling 9
translate-outgoing called 68266
voice-class codec 100
voice-class h323 10
session target ipv4:10.178.196.1
dtmf-relay h245-alphanumeric
ip qos dscp cs5 media
ip qos dscp cs3 signaling
no vad
!
!
!
call-manager-fallback
limit-dn 7940 2
limit-dn 7960 4
timeouts interdigit 5
ip source-address 10.178.203.254 port 2000
max-ephones 24
max-dn 96
dialplan-pattern 1 68266... extension-length 3
keepalive 10
translate called 68266
call-forward busy 68266195
call-forward noan 68266195 timeout 20000
date-format dd-mm-yy
!
!
line con 0
password xxxxxx (moderator edit)
line aux 0
password xxxxxxx (moderator edit)
line vty 0 4
exec-timeout 5 0
password xxxxxx (moderator edit)
!
!
end
01-27-2003 02:10 PM
You can check for known bugs in the Cisco Bug Tool Kit. I found one such bug in the Tool kit, similar to this one. Please check it out.The bug ID is CSCdv75720. The following debugs could help you find out the reasons.
debug vpm sig
debug voip ccapi inout
debug vtsp session
I am not very sure of the solution, if the above bug is the one found in this case.Does anybody has the solution to this?
01-31-2003 02:54 PM
Have you tried using the num-exp command? I am using this and it works very well.
num-exp DID EXTENSION
for example: num-exp 7035551212 3062
Geoff
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide