Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

CAS MGCP

I am trying to get a CAS T1 working with CCM 4.1(3). I can get incomming calls but cannot make outgoing calls. I am going to paste my config below. Please make any suggestions. Also if someone has a verified sample config they could give that would be great.

Thanks

network-clock-participate slot 1

no network-clock-participate wic 0

network-clock-select 1 T1 1/0/0

voice-card 0

no dspfarm

dsp services dspfarm

!

voice-card 1

dspfarm

voice call send-alert

voice rtp send-rec

!

ccm-manager redundant-host 10.0.1.10

ccm-manager mgcp

no ccm-manager fax protocol cisco

ccm-manager music-on-hold

ccm-manager config server 10.0.1.11 10.0.1.10

ccm-manager config

!

controller T1 0/0/0

framing esf

linecode b8zs

!

controller T1 0/0/1

framing esf

linecode b8zs

!

controller T1 1/0/0

framing esf

linecode b8zs

ds0-group 1 timeslots 1-24 type e&m-wink-start

!

interface GigabitEthernet0/0

ip address 10.0.1.2 255.255.255.0

duplex auto

speed auto

media-type rj45

control-plane

!

voice-port 0/1/0

timing hookflash-out 500

!

voice-port 0/1/1

timing hookflash-out 500

!

voice-port 0/2/0

!

voice-port 0/2/1

!

voice-port 0/2/2

!

voice-port 0/2/3

!

voice-port 1/0/0:1

!

mgcp

mgcp call-agent 10.0.1.11 2427 service-type mgcp version 0.1

mgcp dtmf-relay voip codec all mode out-of-band

mgcp rtp unreachable timeout 1000 action notify

mgcp modem passthrough voip mode nse

mgcp package-capability rtp-package

no mgcp package-capability res-package

mgcp package-capability sst-package

no mgcp package-capability fxr-package

mgcp package-capability pre-package

no mgcp timer receive-rtcp

mgcp sdp simple

mgcp fax t38 inhibit

mgcp rtp payload-type g726r16 static

mgcp bind control source-interface GigabitEthernet0/0

mgcp bind media source-interface GigabitEthernet0/0

!

mgcp profile default

!

sccp local GigabitEthernet0/0

sccp ccm 10.0.1.11 identifier 1

sccp ccm 10.0.1.10 identifier 2

sccp

!

sccp ccm group 1

description ***SCCP Conf

associate ccm 1 priority 1

associate ccm 2 priority 2

associate profile 1 register Confbr

associate profile 2 register Xcoder

!

dspfarm profile 2 transcode

description ***Host Xcod DSP Farm

codec g711ulaw

codec g711alaw

codec g729ar8

codec g729abr8

codec gsmfr

maximum sessions 64

associate application SCCP

!

dspfarm profile 1 conference

description ***Host Conf DSP Farm

codec g711ulaw

codec g711alaw

codec g729ar8

codec g729abr8

codec g729r8

codec g729br8

maximum sessions 16

associate application SCCP

!

!

dial-peer voice 99 pots

application mgcpapp

incoming called-number .

port 1/0/0:1

!

dial-peer voice 88 voip

destination-pattern 1010

session target ipv4:10.0.1.10

!

dial-peer voice 999100199 pots

application mgcpapp

port 1/0/0:1

!

dial-peer voice 999020 pots

application mgcpapp

port 0/2/0

!

dial-peer voice 999021 pots

application mgcpapp

port 0/2/1

!

dial-peer voice 999022 pots

application mgcpapp

port 0/2/2

!

dial-peer voice 999010 pots

application mgcpapp

port 0/1/0

!

dial-peer voice 999011 pots

!!

line con 0

login local

stopbits 1

3 REPLIES
Cisco Employee

Re: CAS MGCP

Are you sure the phone's CSS includes the partition for the Route Pattern? I'd look at the app logs on the callmanager, and also the ccm logs.

New Member

Re: CAS MGCP

I will check those but I am pretty sure the CCM routing is correct. I only get a fast busy after the last digit that actually sends the call to the gateway is dialed. Also when the call is sent to the gateway I see a string of messages when I have the debug for mgcp events on. Which seems to indicate the call is tring to pass to the gateway. I have done this many times with PRI with no issues but cannot get this CAS working.

Cisco Employee

Re: CAS MGCP

The gateway message fly by quickly. Usually I start with the ccm traces with mgcp gateways.

Do you have debugging on the gateway?

debug cas

debug vpm signal

debug vtsp all

270
Views
0
Helpful
3
Replies
CreatePlease to create content