10-16-2006 10:11 AM - edited 03-15-2019 04:36 AM
I am receiving the following error at apparently random times:
Cause i = 0x80AC - Requested circuit/channel not available
People try to call in, get a fast busy sometimes, but sometimes connect.
Here are parts of my config:
isdn switch-type primary-ni
voice-card 0
no dspfarm
!
!
!
!
voice service voip
fax protocol pass-through g711ulaw
!
!
voice class codec 101
codec preference 1 g711ulaw
codec preference 2 g729r8
!
!
!
!
!
!
!
!
voice translation-rule 1
rule 1 /removed\(....\)/ /\1/
rule 2 /removed/ /2900/
rule 4 /removed/ /2310/
rule 5 /removed/ /2601/
rule 6 /removed/ /2900/
rule 7 /removed/ /2311/
rule 8 /removed/ /2312/
!
voice translation-rule 2
rule 1 /^011\(44.+\)/ /\1/ type any international plan any isdn
!
!
voice translation-profile Incoming-DID
translate called 1
!
voice translation-profile Outgoing-ISDN
translate called 2
!
!
controller T1 0/2/0
framing esf
clock source line primary
linecode b8zs
pri-group timeslots 1-24
description PRI
!
controller T1 0/2/1
framing esf
linecode b8zs
!
!
interface Serial0/2/0:23
no ip address
isdn switch-type primary-ni
isdn incoming-voice voice
no cdp enable
!
voice-port 0/2/0:23
translation-profile incoming Incoming-DID
translation-profile outgoing Outgoing-ISDN
!
!
dial-peer voice 1025 voip
destination-pattern 25[3-8].
session protocol sipv2
session target sip-server
dtmf-relay rtp-nte
codec g711ulaw
fax protocol pass-through g711ulaw
no vad
!
dial-peer voice 1029 voip
destination-pattern 2900
session protocol sipv2
session target sip-server
incoming called-number 2900T
dtmf-relay rtp-nte
codec g711ulaw
no vad
!
dial-peer voice 100 pots
destination-pattern .+T
direct-inward-dial
port 0/2/0:23
forward-digits all
!
dial-peer voice 2310 voip
destination-pattern 2310
session protocol sipv2
session target sip-server
dtmf-relay rtp-nte
codec g711ulaw
fax protocol pass-through g711ulaw
no vad
!
dial-peer voice 2311 voip
destination-pattern 2311
session protocol sipv2
session target sip-server
dtmf-relay rtp-nte
codec g711ulaw
fax protocol pass-through g711ulaw
no vad
!
dial-peer voice 2312 voip
destination-pattern 2312
session protocol sipv2
session target sip-server
dtmf-relay rtp-nte
codec g711ulaw
fax protocol pass-through g711ulaw
no vad
!
dial-peer voice 2601 voip
destination-pattern 2601
session protocol sipv2
session target sip-server
dtmf-relay rtp-nte
codec g711ulaw
fax protocol pass-through g711ulaw
no vad
!
dial-peer voice 101 voip
voice-class codec 101
incoming called-number .+T
dtmf-relay rtp-nte
!
sip-ua
sip-server ipv4:address removed
!
!
more to follow
10-16-2006 10:11 AM
here are parts of my debug:
Oct 16 12:23:08.147: ISDN Se0/2/0:23 Q931: RX <- SETUP pd = 8 callref = 0x08E0
Bearer Capability i = 0x8090A2
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Facility i = 0x9F8B0100A1080201010201008400
Protocol Profile = Networking Extensions
0xA1080201010201008400
Component = Invoke component
Invoke Id = 1
Operation = CallingName
Name not available
Calling Party Number i = 0x00C3, N/A
Plan:Unknown, Type:Unknown
Called Party Number i = 0xA1, 'removed'
Plan:ISDN, Type:National *Oct 16 12:23:08.151:
//-1/xxxxxxxxxxxx/VTSP:(0/2/0:23):-1:-1:-1/vtsp_allocate_cdb:
CDB=0x666105A8
*Oct 16 12:23:08.151:
//-1/xxxxxxxxxxxx/VTSP:(0/2/0:23):-1:-1:-1/vtsp_do_call_setup_ind:
Event=E_TSP_SETUP_IND
Progress Indication=0, CarrierIDCode=, Info Trans Capability=0, Source Carrier ID=, tg_label_flag=0 *Oct 16 12:23:08.151:
//-1/xxxxxxxxxxxx/VTSP:(0/2/0:23):-1:-1:-1/vtsp_do_call_setup_ind:
Called Number=2900, TON=National, NPI=ISDN *Oct 16 12:23:08.151:
//-1/EA559B8288E1/VTSP:(0/2/0:23):0:-1:-1/vtsp_do_normal_call_setup_ind:
*Oct 16 12:23:08.151: //-1/EA559B8288E1/VTSP:(0/2/0:23):0:-1:-1/vtsp_timer:
Timer Start Time=163369438, Timer Value=180000(ms) *Oct 16 12:23:08.151:
//-1/EA559B8288E1/VTSP:(0/2/0:23):0:-1:-1/vtsp_do_normal_call_setup_ind:
IC State Machine (ICSM) Added
*Oct 16 12:23:08.151:
//-1/EA559B8288E1/VTSP:(0/2/0:23):0:-1:-1/vtsp_insert_cdb:
*Oct 16 12:23:08.151: flex_dsprm_vtsp_open - ACTIVE CALL *Oct 16
12:23:08.151:
//-1/EA559B8288E1/VTSP:(0/2/0:23):0:-1:-1/vtsp_dsm_opened_cb:
*Oct 16 12:23:08.151:
//-1/EA559B8288E1/VTSP:(0/2/0:23):0:-1:-1/vtsp_process_event:
[state:S_SETUP_IND_PEND, event:E_VTSP_DSM_OPEN_FAILURE] *Oct 16
12:23:08.151:
//-1/EA559B8288E1/VTSP:(0/2/0:23):0:-1:-1/act_setup_ind_pend_failure:
Cause Value=172
*Oct 16 12:23:08.151: ISDN Se0/2/0:23 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x88E0
Cause i = 0x80AC - Requested circuit/channel not available *Oct 16
12:23:08.151:
//-1/EA559B8288E1/VTSP:(0/2/0:23):0:-1:-1/vtsp_process_event:
[state:S_SETUP_FAIL, event:E_TSP_DISCONNECT_CONF] *Oct 16 12:23:08.151:
//-1/EA559B8288E1/VTSP:(0/2/0:23):0:-1:-1/act_setup_fail:
*Oct 16 12:23:08.151:
//-1/EA559B8288E1/VTSP:(0/2/0:23):0:-1:-1/act_setup_fail:exit@475
*Oct 16 12:23:08.151:
//-1/EA559B8288E1/VTSP:(0/2/0:23):0:-1:-1/act_terminate:
*Oct 16 12:23:08.151:
//-1/EA559B8288E1/VTSP:(0/2/0:23):0:-1:-1/vtsp_set_release_source:
Release Direction=PSTN, Release Source=Calling Party-PSTN *Oct 16
12:23:08.151:
//-1/EA559B8288E1/VTSP:(0/2/0:23):0:-1:-1/vtsp_timer_stop:
Timer Stop Time=163369438
*Oct 16 12:23:08.151:
//-1/EA559B8288E1/VTSP:(0/2/0:23):0:-1:-1/vtsp_free_cdb:
CDB=0x666105A8
NOTE: Anywhere you see removed is because I removed the address/phone number.
Anyone have any idea what I need to do?
10-16-2006 12:50 PM
Just so everyone knows, there is a bug in the IOS. I know, I am just as surprised as everyone else is!
The bug id is CSCsb12638
No need to reply to this thread.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide