Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Cause i = 0x80E4 - Invalid information element contents in debug isdn q931

Hi,

5350 is configured with T1 PRI. i did the debug isdn q931 and i found this message in every call. Calls are coming and going out properly. A little debug isdn q931 for your consideration:

*Mar 21 08:29:35: ISDN Se3/0:23: overriding plan/type for 0292299128, isdn/national to isdn/subscriber

*Mar 21 08:29:35: ISDN Se3/0:23: overriding plan/type for 0292299128, data/unknown to isdn/subscriber

*Mar 21 08:29:35: ISDN Se3/0:23: TX -> SETUP pd = 8 callref = 0x6562

*Mar 21 08:29:35: Bearer Capability i = 0x8090A2

*Mar 21 08:29:35: Channel ID i = 0xA98397

*Mar 21 08:29:35: Calling Party Number i = 'A', 0x83, '0292299128', Plan:ISDN, Type:Subscriber(local)

*Mar 21 08:29:35: Called Party Number i = 0xC1, '49146467', Plan:ISDN, Type:Subscriber(local)

*Mar 21 08:29:35: ISDN Se3/0:23: RX <- CALL_PROC pd = 8 callref = 0xE562

*Mar 21 08:29:35: Channel ID i = 0xA98397

*Mar 21 08:29:35: ISDN Se3/0:23: RX <- PROGRESS pd = 8 callref = 0xE562

*Mar 21 08:29:35: Progress Ind i = 0x8288 - In-band info or appropriate now available

*Mar 21 08:29:42: ISDN Se3/0:23: RX <- SETUP pd = 8 callref = 0x7E7A

*Mar 21 08:29:42: Bearer Capability i = 0x8090A2

*Mar 21 08:29:42: Channel ID i = 0xA98381

*Mar 21 08:29:42: Calling Party Number i = 0x00A0, '009001', Plan:Unknown, Type:Unknown

*Mar 21 08:29:42: Called Party Number i = 0xC1, '49204337', Plan:ISDN, Type:Subscriber(local)

*Mar 21 08:29:42: ISDN Se3/0:23: TX -> CALL_PROC pd = 8 callref = 0xFE7A

*Mar 21 08:29:42: Channel ID i = 0xA98381

*Mar 21 08:29:43: ISDN Se3/0:23: RX <- ALERTING pd = 8 callref = 0xE562

*Mar 21 08:29:44: ISDN Se3/0:23: RX <- DISCONNECT pd = 8 callref = 0x7E7A

*Mar 21 08:29:44: Cause i = 0x80A930 - Temporary failure

*Mar 21 08:29:44: ISDN Se3/0:23: TX -> RELEASE pd = 8 callref = 0xFE7A

*Mar 21 08:29:44: Cause i = 0x80E4 - Invalid information element contents

*Mar 21 08:29:44: ISDN Se3/0:23: RX <- RELEASE_COMP pd = 8 callref = 0x7E7A

*Mar 21 08:29:45: ISDN Se3/1:23: RX <- SETUP pd = 8 callref = 0x34A0

*Mar 21 08:29:45: Bearer Capability i = 0x8090A2

*Mar 21 08:29:45: Channel ID i = 0xA98381

*Mar 21 08:29:45: Calling Party Number i = 0x80, '0821653159', Plan:Unknown, Type:Unknown

*Mar 21 08:29:45: Called Party Number i = 0xC1, '992955993', Plan:ISDN, Type:Subscriber(local)

*Mar 21 08:29:45: ISDN Se3/1:23: TX -> CALL_PROC pd = 8 callref = 0xB4A0

*Mar 21 08:29:45: Channel ID i = 0xA98381un all

*Mar 21 08:29:50: ISDN Se3/1:23: TX -> ALERTING pd = 8 callref = 0xB4A0

*Mar 21 08:29:50: Progress Ind i = 0x8188 - In-band info or appropriate now available

*Mar 21 08:29:56: ISDN Se3/1:23: TX -> CONNECT pd = 8 callref = 0xB4A0

*Mar 21 08:29:56: Progress Ind i = 0x8182 - Destination address is non-ISDN

*Mar 21 08:29:56: ISDN Se3/1:23: RX <- STATUS pd = 8 callref = 0x34A0

*Mar 21 08:29:56: Cause i = 0x80E31E - Information element not implemented

*Mar 21 08:29:56: Call State i = 0x08

*Mar 21 08:29:56: ISDN Se3/1:23: RX <- CONNECT_ACK pd = 8 callref = 0x34A0

*Mar 21 08:29:56: ISDN Se3/1:23: CALL_PROGRESS: CALL_CONNECTED call id 0x1B6E, bchan 0, dsl 1

*Mar 21 08:30:05: ISDN Se3/0:23: RX <- CONNECT pd = 8 callref = 0xE562

*Mar 21 08:30:05: ISDN Se3/0:23: TX -> CONNECT_ACK pd = 8 callref = 0x6562

*Mar 21 08:30:07: ISDN Se3/0:23: TX -> DISCONNECT pd = 8 callref = 0x6562

*Mar 21 08:30:07: Cause i = 0x8090 - Normal call clearing

*Mar 21 08:30:08: ISDN Se3/0:23: RX <- RELEASE pd = 8 callref = 0xE562

*Mar 21 08:30:08: ISDN Se3/0:23: TX -> RELEASE_COMP pd = 8 callref = 0x6562

*Mar 21 08:30:24: ISDN Se3/1:23: RX <- DISCONNECT pd = 8 callref = 0x34A0

*Mar 21 08:30:24: Cause i = 0x809F30 - Normal, unspecified

*Mar 21 08:30:24: ISDN Se3/1:23: TX -> RELEASE pd = 8 callref = 0xB4A0

*Mar 21 08:30:24: Cause i = 0x80E4 - Invalid information element contents

*Mar 21 08:30:24: ISDN Se3/1:23: RX <- RELEASE_COMP pd = 8 callref = 0x34A0

*Mar 21 08:30:27: ISDN Se3/0:23: overriding plan/type for 0292299128, isdn/national to isdn/subscriber

*Mar 21 08:30:27: ISDN Se3/0:23: overriding plan/type for 0292299128, data/unknown to isdn/subscriber

*Mar 21 08:30:27: ISDN Se3/0:23: TX -> SETUP pd = 8 callref = 0x6563

*Mar 21 08:30:27: Bearer Capability i = 0x8090A2

*Mar 21 08:30:27: Channel ID i = 0xA98397

*Mar 21 08:30:27: Calling Party Number i = 'A', 0x83, '0292299128', Plan:ISDN, Type:Subscriber(local)

*Mar 21 08:30:27: Called Party Number i = 0xC1, '47446467', Plan:ISDN, Type:Subscriber(local)

*Mar 21 08:30:27: ISDN Se3/0:23: RX <- CALL_PROC pd = 8 callref = 0xE563

*Mar 21 08:30:27: Channel ID i = 0xA98397

*Mar 21 08:30:27: ISDN Se3/0:23: RX <- PROGRESS pd = 8 callref = 0xE563

*Mar 21 08:30:27: Progress Ind i = 0x8288 - In-band info or appropriate now available

*Mar 21 08:30:35: ISDN Se3/0:23: RX <- ALERTING pd = 8 callref = 0xE563

*Mar 21 08:30:35: ISDN Se3/0:23: RX <- CONNECT pd = 8 callref = 0xE563

*Mar 21 08:30:35: ISDN Se3/0:23: TX -> CONNECT_ACK pd = 8 callref = 0x6563

*Mar 21 08:30:36: ISDN Se3/0:23: overriding plan/type for 0292399766, isdn/national to isdn/subscriber

*Mar 21 08:30:36: ISDN Se3/0:23: overriding plan/type for 0292399766, data/unknown to isdn/subscriber

*Mar 21 08:30:36: ISDN Se3/0:23: TX -> SETUP pd = 8 callref = 0x6564

*Mar 21 08:30:36: Bearer Capability i = 0x8090A2

*Mar 21 08:30:36: Channel ID i = 0xA98396

*Mar 21 08:30:36: Calling Party Number i = 'A', 0x83, '0292399766', Plan:ISDN, Type:Subscriber(local)

*Mar 21 08:30:36: Called Party Number i = 0xC1, '494190579', Plan:ISDN, Type:Subscriber(local)

*Mar 21 08:30:36: ISDN Se3/0:23: RX <- CALL_PROC pd = 8 callref = 0xE564

*Mar 21 08:30:36: Channel ID i = 0xA98396

*Mar 21 08:30:36: ISDN Se3/0:23: RX <- PROGRESS pd = 8 callref = 0xE564

*Mar 21 08:30:36: Progress Ind i = 0x8288 - In-band info or appropriate now available

*Mar 21 08:30:39: ISDN Se3/0:23: RX <- ALERTING pd = 8 callref = 0xE564

*Mar 21 08:30:49: ISDN Se3/0:23: RX <- DISCONNECT pd = 8 callref = 0xE563

*Mar 21 08:30:49: Cause i = 0x809030 - Normal call clearing

*Mar 21 08:30:49: ISDN Se3/0:23: TX -> RELEASE pd = 8 callref = 0x6563

*Mar 21 08:30:49: Cause i = 0x80E4 - Invalid information element contents

*Mar 21 08:30:49: ISDN Se3/0:23: RX <- RELEASE_COMP pd = 8 callref = 0xE563

*Mar 21 08:30:50: ISDN Se3/1:23: RX <- SETUP pd = 8 callref = 0x35A0

*Mar 21 08:30:50: Bearer Capability i = 0x9090A2

*Mar 21 08:30:50: Channel ID i = 0xA98381

Configuration:

interface Serial3/0:23

no ip address

no logging event link-status

isdn switch-type primary-dms100

isdn not-end-to-end 64

isdn incoming-voice modem 64

isdn map address .* plan isdn type subscriber

fair-queue 64 256 0

no cdp enable

!

interface Serial3/1:23

no ip address

no logging event link-status

isdn switch-type primary-dms100

isdn not-end-to-end 64

isdn incoming-voice modem 64

isdn map address .* plan isdn type subscriber

fair-queue 64 256 0

no cdp enable

!

voice-port 3/0:D

echo-cancel coverage 16

timeouts initial 30

timeouts interdigit 5

timeouts ringing 30

bearer-cap Speech

!

voice-port 3/1:D

echo-cancel coverage 16

timeouts initial 30

timeouts interdigit 5

timeouts ringing 30

bearer-cap Speech

!

System image file is "flash:c5350-is-mz.121-5.XM8.bin" default with my 5350.

Any help will higly be appriciated. Thanks

  • Other Collaboration Voice and Video Subjects
2 REPLIES
New Member

Re: Cause i = 0x80E4 - Invalid information element contents in d

Looks like it is from the router side:

0x80E4

The remote equipment receives a message that includes invalid information in the information element.

This cause indicates that the equipment sending this has received an information element which it has implemented; however, one or more of the fields in the information element are coded in a way that has not been implemented by the equipment sending this cause.

This is due to a D-channel error

http://www.cisco.com/warp/public/129/isdn_disc_code.html

New Member

Re: Cause i = 0x80E4 - Invalid information element contents in d

Hey,

thanks for your attention. I was thinking to give some more details on network topology.

Originating site--------------------Internet--------------------Terminating side

E1 PRI (basic-net3)-------------------------------------------- T1 PRI (primary-dms100)

!

Originating side config:

!

interface Serial0:15

no ip address

isdn switch-type primary-net5

isdn overlap-receiving

isdn not-end-to-end 64

isdn protocol-emulate network

isdn incoming-voice modem 64

isdn map address .* plan isdn type subscriber

isdn T310 60000

no isdn outgoing display-ie

fair-queue 64 256 0

no cdp enable

!

!

voice-port 0:D

echo-cancel coverage 16

cptone FR

timeouts initial 30

timeouts ringing 60

timeouts wait-release 3

bearer-cap Speech

!

ISDN 0:D - 0:D

Type of VoicePort is ISDN

Operation State is DORMANT

Administrative State is UP

No Interface Down Failure

Description is not set

Noise Regeneration is enabled

Non Linear Processing is enabled

Non Linear Mute is disabled

Non Linear Threshold is -21 dB

Music On Hold Threshold is Set to -38 dBm

In Gain is Set to 0 dB

Out Attenuation is Set to 0 dB

Echo Cancellation is enabled

Echo Cancellation NLP mute is disabled

Echo Cancellation NLP threshold is -21 dB

Echo Cancel Coverage is set to 16 ms

Playout-delay Mode is set to adaptive

Playout-delay Nominal is set to 60 ms

Playout-delay Maximum is set to 200 ms

Playout-delay Minimum mode is set to default, value 40 ms

Playout-delay Fax is set to 300 ms

Connection Mode is normal

Connection Number is not set

Initial Time Out is set to 30 s

Interdigit Time Out is set to 10 s

Call Disconnect Time Out is set to 60 s

Ringing Time Out is set to 60 s

Wait Release Time Out is set to 3 s

Companding Type is A-law

Region Tone is set for FR

Station name None, Station number None

Translation profile (Incoming):

Translation profile (Outgoing):

!

Terminating Side Config:

!

interface Serial3/0:23

no ip address

no logging event link-status

isdn switch-type primary-dms100

isdn not-end-to-end 64

isdn incoming-voice modem 64

isdn map address .* plan isdn type subscriber

fair-queue 64 256 0

no cdp enable

!

!

voice-port 3/0:D

echo-cancel coverage 16

timeouts initial 30

timeouts interdigit 5

timeouts ringing 30

bearer-cap Speech

!

ISDN 3/0:D - 3/0:D

Type of VoicePort is ISDN

Operation State is DORMANT

Administrative State is UP

No Interface Down Failure

Description is not set

Noise Regeneration is enabled

Non Linear Processing is enabled

Music On Hold Threshold is Set to -38 dBm

In Gain is Set to 0 dB

Out Attenuation is Set to 0 dB

Echo Cancellation is enabled

Echo Cancel Coverage is set to 16 ms

Playout-delay Mode is set to default

Playout-delay Nominal is set to 60 ms

Playout-delay Maximum is set to 200 ms

Playout-delay Minimum mode is set to default, value 40 ms

Connection Mode is normal

Connection Number is not set

Initial Time Out is set to 30 s

Interdigit Time Out is set to 5 s

Ringing Time Out is set to 30 s

Companding Type is u-law

Region Tone is set for US

Wait Release Time Out is 30 s

Station name None, Station number None

!

Hope this might help us to solve the issue.

5437
Views
0
Helpful
2
Replies
This widget could not be displayed.