Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

CCM - voip gateway - PBX Integration

CCM ver3.3 is configured by using router-patterns and H.323 gateway configurations so that I can initiate a call from IP Phones through gateways (then ended at a PBX subscriber). However, the other way around does not work.

CCM: 10.81.50.2

IP Phone: 10.81.50.11

1st button on 7640: 3302

2nd button on 7640: 3304

Cisco 3640 H.323 gateway: 10.81.3.161

PBX is connected to Cisco 3640 via PRI trunk, HDV..

If it was initiated from IP Phones, call is established. Else if, call is droped if it is initiated from PBX.

Configurations are as follows:

IP Phone button 1: 3302

IP Phone button 2: 3304

CCM:

Route-pattern configs..

If 3XXX then forward to G/W:10.81.3.161 with a prefix 2

If XXXX then forward to G/W:10.81.3.161 with a prefix 2

Router 3640:

!

voice class codec 1

codec preference 1 g729r8

codec preference 2 g729br8

codec preference 3 g711ulaw

codec preference 4 g711alaw

!

!

interface Serial1/0:15

no ip address

no ip route-cache cef

no logging event link-status

no snmp trap link-status

isdn switch-type primary-qsig

isdn incoming-voice voice

isdn disconnect-cause 3

no cdp enable

!

!

voice-port 1/0:15

input gain -4

output attenuation 4

cptone TR

!

!

dial-peer voice 30 pots

destination-pattern 2....

direct-inward-dial

port 1/0:15

!

!

dial-peer voice 21 voip

destination-pattern 3302

voice-class codec 1

session target ipv4:10.81.50.2

ip precedence 5

!

Returned disc cause was: 3 "no route to destination".

Evenif I removed 3XXX and XXXX routes from the route-pattern list, same disc. cause returned from CCM to router.

Thanks for aid,

Onur

2 REPLIES
New Member

Re: CCM - voip gateway - PBX Integration

I take it your 3303 and 3304 DNs are a subrange of your PABX, so you are forwarding all non-CCM registered DNs out the gateway.

When you say cause code 3 in the PABX->CCM direction what was the contents of the setup message in the Debug H225 Q931? Looks like you have a translation problem on the digits or a partition/calling search space issue

Rory

New Member

Re: CCM - voip gateway - PBX Integration

I found the mistake. On the 3640 router, I have configure Loopback0 as H.323 interface for registering onto gatekeeper and initiating the voice call.

!

interface Loopback0

ip address 10.81.193.19 255.255.255.255

h323-gateway voip interface

h323-gateway voip id gk-uom ipaddr 10.81.3.160 1718

h323-gateway voip h323-id UOM_VOIP

h323-gateway voip bind srcaddr 10.81.193.19

!

interface Ethernet0/0

ip address 10.81.3.161 255.255.255.128

half-duplex

!

But on the CCM, I have defined route-pattern as through 10.81.3.161 instread of 10.81.193.19. When I changed the route-pattern as loopback 0 address of Cisco 3640, system became operational.

Onur

499
Views
0
Helpful
2
Replies
CreatePlease to create content