Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

CCME moh Muzak

Has anyone ever connected a Muzak system for moh to a ccme router?

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Red

Re: CCME moh Muzak

Hi Christopher,

I have not done this, but it certainly is supported on CME. The details are noted below;

Configuring Music on Hold from a Live Feed

To configure music on hold from a live feed, perform the following steps.

Prerequisites

•SIP phones require Cisco Unified CME 4.1 or a later version.

•VIC2-2FXO, VIC2-4FXO, EM-HDA-3FXS/4FXO, EM-HDA-6FXO, or EM2-HDA-4FXO

•For a live feed from VoIP, VAD must be disabled.

Restrictions

•A foreign exchange station (FXS) port cannot be used for a live feed.

SUMMARY STEPS

1. enable

2. configure terminal

3. voice-port port

4. input gain decibels

5. auto-cut-through (E&M only)

6. operation 4-wire (E&M only)

7. signal immediate (E&M only)

8. signal loop-start live-feed (FXO only)

9. no shutdown

10. exit

11. dial peer voice tag pots

12. destination-pattern string

13. port port

14. exit

15. ephone-dn dn-tag

16. number number

17. moh [out-call outcall-number] [ip ip-address port port-number [route ip-address-list]]

18. exit

19. ephone phone-tag

20. multicast-moh

21. end

From this good CME doc (with detailed steps);

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmemoh.html#wp1010511

Hope this helps!

Rob

2 REPLIES
Hall of Fame Super Red

Re: CCME moh Muzak

Hi Christopher,

I have not done this, but it certainly is supported on CME. The details are noted below;

Configuring Music on Hold from a Live Feed

To configure music on hold from a live feed, perform the following steps.

Prerequisites

•SIP phones require Cisco Unified CME 4.1 or a later version.

•VIC2-2FXO, VIC2-4FXO, EM-HDA-3FXS/4FXO, EM-HDA-6FXO, or EM2-HDA-4FXO

•For a live feed from VoIP, VAD must be disabled.

Restrictions

•A foreign exchange station (FXS) port cannot be used for a live feed.

SUMMARY STEPS

1. enable

2. configure terminal

3. voice-port port

4. input gain decibels

5. auto-cut-through (E&M only)

6. operation 4-wire (E&M only)

7. signal immediate (E&M only)

8. signal loop-start live-feed (FXO only)

9. no shutdown

10. exit

11. dial peer voice tag pots

12. destination-pattern string

13. port port

14. exit

15. ephone-dn dn-tag

16. number number

17. moh [out-call outcall-number] [ip ip-address port port-number [route ip-address-list]]

18. exit

19. ephone phone-tag

20. multicast-moh

21. end

From this good CME doc (with detailed steps);

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmemoh.html#wp1010511

Hope this helps!

Rob

New Member

Re: CCME moh Muzak

Thanks Rob, I have seen that document before, just curious if anyone has ever done this before. I got it working by following the steps above, worked first time, not bad at all.

493
Views
0
Helpful
2
Replies