Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
907
Views
5
Helpful
11
Replies

Cisco 5300 DSPM / C549 and software vfc upgrade

lterebizh
Level 1
Level 1

‎08-27-2002 09:54 PM - edited ‎03-12-2019 08:32 PM

Question is:

If I put version 7 to vfc then it going to work. But I'd like to know what is the differences between DSPM boards or between C549 or between AS itself that let it have last vfc software.........

Here is some info:

Router#show vfc 1 version vcware

Voice Feature Card in Slot 1:

VCWare Version : 9.20a

ROM Monitor Version: 1.3

DSPWare Version : 3.6.16aL

Technology : C549

Firmware version mismatch for bundle AS5300 VCWare

- version found (9.20a) is higher than maximum allowed (7.xx)

Firmware version mismatch for bundle AS5300 C549

- version found (3.6.16aL) is higher than maximum allowed (3.4.xxL)

Router#show vfc 1 version dspware

DSPWare version in VFC slot 1 is 3.6.16aL

Firmware version mismatch for bundle AS5300 VCWare

- version found (9.20a) is higher than maximum allowed (7.xx)

Firmware version mismatch for bundle AS5300 C549

- version found (3.6.16aL) is higher than maximum allowed (3.4.xxL)

Labels:
0 Helpful
11 Replies 11

b.mason
Level 1
Level 1

‎08-27-2002 10:25 PM

Go to this URL:

http://www.cisco.com/univercd/cc/td/doc/product/access/acs_serv/5300/sw_conf/vcw_rn/rnvcware.htm#xtocid5

It has a vfc/ios compatibility matrix. So shows you what vfc version should be run with each IOS version. So if you require something in a later vfc then you also need to upgrade your IOS to match.

lterebizh
Level 1
Level 1
In response to b.mason

‎08-27-2002 10:39 PM

Sorry it is not work...

I read this and many others before I did posting...

:-)

So I tried matching version for latest versions.... NO luck...

0 Helpful

b.mason
Level 1
Level 1
In response to lterebizh

‎08-27-2002 11:11 PM

What version of IOS are you running?

0 Helpful

lterebizh
Level 1
Level 1
In response to b.mason

‎08-28-2002 07:17 AM

c5300-js-mz.122-2.XB6.bin which is ENTERPRISE VOICE PLUS

And I tried vcware 9.19 and 9.20a.

0 Helpful

b.mason
Level 1
Level 1

‎08-28-2002 07:15 PM

Can you please paste in the output of the command 'show ver'

0 Helpful

lterebizh
Level 1
Level 1
In response to b.mason

‎08-28-2002 08:51 PM

This is message that I am worry about....

00:00:58: DSPM 1 (type C542) in slot 1 is incompatible with installed VCWare (type C549)

00:00:58: DSPM 2 (type C542) in slot 1 is incompatible with installed VCWare (type C549)

00:00:58: DSPM 3 (type C542) in slot 1 is incompatible with installed VCWare (type C549)

00:00:58: DSPM 4 (type C542) in slot 1 is incompatible with installed VCWare (type C549)

Now I am trying use c5300-js-mz.122-11.T.bin

and vcw-vfc-mz.c549.hc.10.26.bin

And vcm do not unbind... Just says that it is and it is not....

First moment after boot I can see

24 DSP(s), 24 Voice resource(s)

Then after few seconds

24 DSP(s), 48 Voice resource(s)

This is full sh ver:

System image file is "flash:c5300-js-mz.122-11.T.bin"

cisco AS5300 (R4K) processor (revision A.32) with 131072K/16384K bytes of memory.

Processor board ID 10077465

R4700 CPU at 150Mhz, Implementation 33, Rev 1.0, 512KB L2 Cache

Bridging software.

X.25 software, Version 3.0.0.

SuperLAT software (copyright 1990 by Meridian Technology Corp).

TN3270 Emulation software.

Primary Rate ISDN software, Version 1.1.

Backplane revision 2

Manufacture Cookie Info:

EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x30,

Board Hardware Version 1.64, Item Number 800-2544-02,

Board Revision B0, Serial Number 10077465,

PLD/ISP Version 0.0, Manufacture Date 22-Sep-1998.

1 Ethernet/IEEE 802.3 interface(s)

1 FastEthernet/IEEE 802.3 interface(s)

4 Channelized T1/PRI port(s)

24 DSP(s), 48 Voice resource(s)

128K bytes of non-volatile configuration memory.

16384K bytes of processor board System flash (Read/Write)

8192K bytes of processor board Boot flash (Read/Write)

Router#sh vfc 1 v v

Voice Feature Card in Slot 1:

VCWare Version : 10.26

ROM Monitor Version: 1.3

DSPWare Version : 4.0.26

Technology : C549

VCWare/DSPWare version compatibility OK

Router#sh vfc 1 v d

DSPWare version in VFC slot 1 is 4.0.26

VCWare/DSPWare version compatibility OK

Router#sh vfc 1 di

Files in slot 1 VFC flash:

File Name Size (Bytes)

1 . vcw-vfc-mz.c549.hc.10.26.bin 471548

Router#sh vfc 1 ca

Capability List for VFC in slot 1:

1. cor-vfc-hc-l.4.0.26.bin

2. bas-vfc-hc-l.4.0.26.bin

3. fxb-vfc-hc-l.4.0.26.bin

4. fax-vfc-hc-l.4.0.26.bin

5. cdc-g711-hc-l.4.0.26.bin

6. cdc-g726-hc-l.4.0.26.bin

7. cdc-g729-hc-l.4.0.26.bin

8. cdc-g728-hc-l.4.0.26.bin

9. cdc-g723.1-hc-l.4.0.26.bin

10. cdc-gsmfr-hc-l.4.0.26.bin

11. cdc-gefr-hc-l.4.0.26.bin

=========================================================

Then I put c5300-js-mz.122-10a.bin

and vcw-vfc-mz.c549.hc.7.40.bin

And it seems OK...I mean it (vcw) was unbundled...

And at boot I can see

The same.....

========================

Bottom line....

I feel that software IOS OK and VCWare as well...But ...This starting message and that fact that I see 24 voices at first and 48 then....

The only thing I can think - This voice boards have C549 and some jumpers in the board ....So this jumpers are too tall and I am checking board with only one DSPM module in (I thought just cut them to be able insert 2 boards)...

I have label DSP ver 2.1 on this boards...

So what can you say....

0 Helpful

b.mason
Level 1
Level 1
In response to lterebizh

‎08-28-2002 11:37 PM

Oh ok now it makes sense.

There are two different VFC technologies, C542 & C549. So if you remove current vfc file and install vcw-vfc-mz.c542.10.26.bin instead it should be fine.

0 Helpful

lterebizh
Level 1
Level 1
In response to b.mason

‎08-29-2002 07:01 AM

May be I was not clear...

Boards are with C549 chips.... So I know for sure wich technology I have...

Problem are somewhere else....

Should those messages comes in any box.... Or it is just this one 5300 problem....

May be I shouldupgrade boot flash .... I am not sure....

0 Helpful

b.mason
Level 1
Level 1
In response to lterebizh

‎08-29-2002 05:03 PM

Just so I'm clear on the problem can you please paste the output from the following commands:

show vfc 1 interface

show vfc 1 v v

0 Helpful

lterebizh
Level 1
Level 1
In response to b.mason

‎08-29-2002 06:09 PM

This time I have 2 vfc and it is wierd that one DSP is OK and others not....

Nut all are the same... at least visual.....

=========================

Router#sh vfc 1 int

Rx: in ptr 26, outptr 0

Tx: in ptr 21 outptr 21

0 in hw queue, 0 queue head , 0 queue tail

Hardware is VFC out-of-band channel

Interface : state RESET DSP instance (0x61CE30DC)

dsp_number 0, Channel ID 0

tx outstanding 0, max tx outstanding 0

Received 26 packets, 1317 bytes, 0 giant packets

0 drops, 0 no buffers, 0 input errors

190 bytes output, 21 frames output

0 bounce errors 0

DSP module 1 is not installed

DSP module 2 is not installed

DSP module 3 is not installed

Slot 1, DSPM 4 (C549), DSP 1, Channel 1

State DSP CODEC READY, DSP instance (0x61D44C18)

tx outstanding 0, max tx outstanding 8

Received 0 packets, 0 bytes, 0 giant packets

0 drops, 0 no buffers, 0 input errors

0 bytes output, 0 frames output

0 bounce errors 0

Slot 1, DSPM 4 (C549), DSP 1, Channel 2

State DSP CODEC READY, DSP instance (0x61D44D64)

tx outstanding 0, max tx outstanding 8

Received 0 packets, 0 bytes, 0 giant packets

0 drops, 0 no buffers, 0 input errors

0 bytes output, 0 frames output

0 bounce errors 0

Slot 1, DSPM 4 (C549), DSP 2, Channel 1

State DSP CODEC READY, DSP instance (0x61D45148)

tx outstanding 0, max tx outstanding 8

Received 0 packets, 0 bytes, 0 giant packets

0 drops, 0 no buffers, 0 input errors

0 bytes output, 0 frames output

0 bounce errors 0

Slot 1, DSPM 4 (C549), DSP 2, Channel 2

State DSP CODEC READY, DSP instance (0x61D45294)

tx outstanding 0, max tx outstanding 8

Received 0 packets, 0 bytes, 0 giant packets

0 drops, 0 no buffers, 0 input errors

0 bytes output, 0 frames output

0 bounce errors 0

Slot 1, DSPM 4 (C549), DSP 3, Channel 1

State DSP CODEC READY, DSP instance (0x61D45678)

tx outstanding 0, max tx outstanding 8

Received 0 packets, 0 bytes, 0 giant packets

0 drops, 0 no buffers, 0 input errors

0 bytes output, 0 frames output

0 bounce errors 0

Slot 1, DSPM 4 (C549), DSP 3, Channel 2

State DSP CODEC READY, DSP instance (0x61D457C4)

tx outstanding 0, max tx outstanding 8

Received 0 packets, 0 bytes, 0 giant packets

0 drops, 0 no buffers, 0 input errors

0 bytes output, 0 frames output

0 bounce errors 0

Slot 1, DSPM 4 (C549), DSP 4, Channel 1

State DSP CODEC READY, DSP instance (0x61D45BA8)

tx outstanding 0, max tx outstanding 8

Received 0 packets, 0 bytes, 0 giant packets

0 drops, 0 no buffers, 0 input errors

0 bytes output, 0 frames output

0 bounce errors 0

Slot 1, DSPM 4 (C549), DSP 4, Channel 2

State DSP CODEC READY, DSP instance (0x61D45CF4)

tx outstanding 0, max tx outstanding 8

Received 0 packets, 0 bytes, 0 giant packets

0 drops, 0 no buffers, 0 input errors

0 bytes output, 0 frames output

0 bounce errors 0

Slot 1, DSPM 4 (C549), DSP 5, Channel 1

State DSP CODEC READY, DSP instance (0x61D460D8)

tx outstanding 0, max tx outstanding 8

Received 0 packets, 0 bytes, 0 giant packets

0 drops, 0 no buffers, 0 input errors

0 bytes output, 0 frames output

0 bounce errors 0

Slot 1, DSPM 4 (C549), DSP 5, Channel 2

State DSP CODEC READY, DSP instance (0x61D46224)

tx outstanding 0, max tx outstanding 8

Received 0 packets, 0 bytes, 0 giant packets

0 drops, 0 no buffers, 0 input errors

0 bytes output, 0 frames output

0 bounce errors 0

Slot 1, DSPM 4 (C549), DSP 6, Channel 1

State DSP CODEC READY, DSP instance (0x61D46608)

tx outstanding 0, max tx outstanding 8

Received 0 packets, 0 bytes, 0 giant packets

0 drops, 0 no buffers, 0 input errors

0 bytes output, 0 frames output

0 bounce errors 0

Slot 1, DSPM 4 (C549), DSP 6, Channel 2

State DSP CODEC READY, DSP instance (0x61D46754)

tx outstanding 0, max tx outstanding 8

Received 0 packets, 0 bytes, 0 giant packets

0 drops, 0 no buffers, 0 input errors

0 bytes output, 0 frames output

0 bounce errors 0

DSP module 5 is not installed

Router#sh vfc 1 v v

Voice Feature Card in Slot 1:

VCWare Version : 7.40

ROM Monitor Version: 1.3

DSPWare Version : 3.4.51L

Technology : C549

VCWare/DSPWare version compatibility OK

=====================================================

Router#sh vfc 2 int

Rx: in ptr 20, outptr 0

Tx: in ptr 15 outptr 15

0 in hw queue, 0 queue head , 0 queue tail

Hardware is VFC out-of-band channel

Interface : state RESET DSP instance (0x61D48FDC)

dsp_number 0, Channel ID 0

tx outstanding 0, max tx outstanding 0

Received 20 packets, 1233 bytes, 0 giant packets

0 drops, 0 no buffers, 0 input errors

130 bytes output, 15 frames output

0 bounce errors 0

DSP module 1 is not installed

DSP module 2 is not installed

DSP module 3 is not installed

DSP module 4 is not installed

DSP module 5 is not installed

Router#sh vfc 2 v v

Voice Feature Card in Slot 2:

VCWare Version : 7.40

ROM Monitor Version: 1.3

DSPWare Version : 3.4.51L

Technology : C549

VCWare/DSPWare version compatibility OK

Route

0 Helpful

b.mason
Level 1
Level 1
In response to lterebizh

‎08-29-2002 06:49 PM

I tested this on 2 as5300 and got similar results. It seems to be a bug?

I'm talking to TAC now to try and find out what is going on.

I will let you know the outcome when I know more.

0 Helpful
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Customers Also Viewed These Support Documents