Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Cisco QSIG and Alcatel 4200 OmniPcx

Hello,

I have the telephone company networking different manufacturers using QSIG and a PRI and BRI interfaces. General below:

Code:

88XX <-> PBX A <-> A Cisco router BRI / PRI <-> B Cisco router BRI / PRI <-> PBX B (Alcetel 4200 OmniPcx) <-> 99XX

To drive traffic to the relevant central telephone routers and logs from the collection of traffic through the use of CCM configurations on the router, etc. ...:

Code:

dial-peer voice 99 voip

destination-pattern 99.

progress_ind setup enable 3

voice-class codec 5

session target ipv4: <recipient IP CCM>

dtmf-relay h245-alphanumeric

fax-relay disable ecm

fax nsf 000000

fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback cisco

no vad

Connections operate in both directions from PBX A to PBX B, PBX and vice versa.

In one location Alcatel 4200 PBX OmniPcx which is connected to a router using the BRI and a QSIG. Router with Alcetel layer 1 and 2 will see without any problem.

If the router A settings (session target ipv4: <recipient IP Router B>) and router B settings (session target ipv4: <recipient IP Router A>) to connect the two parties are acting without any reservations.

If I change (session target ipv4: <recipient CCM> IP) trying to connect with PBX A to B to PBX connection is performed without a problem while in the opposite direction from PBX B (Alcetel) to PBX A is a lack of connection

Here dabug ISDN-a:

Code:

ISDN BR0/1/0 Q931: RX <- SETUP pd = 8 callref = 0x0078

Sending Complete

Bearer Capability and 0x8090A3 =

Standard = CCITT

Transfer Capability = Speech

Transfer Mode = Circuit

Transfer Rate = 64 kbit / s

Channel and ID = 0xA98382

Exclusive, Channel 2

Progress Ind., and = 0xA590 - Reserved value

Calling Party Number i = 0x2183,'9988 '

Plan: ISDN, Type: National

Called Party Number i = 0x89,'8888 '

Plan: Private, Type: Unknown

Shift to Codeset 5

Codeset 5 IE = 0x31 and 0x80

ISDN BR0/1/0 Q931: TX -> CALL_PROC pd = 8 callref = 0x8078

Channel and ID = 0xA98382

Exclusive, Channel 2

ISDN BR0/1/0 Q931: TX -> DISCONNECT pd = 8 callref = 0x8078

Cause and = 0x82A6 - Network out of order

ISDN BR0/1/0 Q931: RX <- RELEASE pd = 8 callref = 0x0078

Cause and = 0x819B - Destination out of order

ISDN BR0/1/0 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x8078

Add that the CCM is configured so as to the other PBX which operates without any problem.

Where to find the cause? Is CCM must have a specific setting for Alcetela? Are PBX?

Thank you in advance for your help.

Voisik

1 REPLY
New Member

Re: Cisco QSIG and Alcatel 4200 OmniPcx

Code for good connections:

ISDN BR0/1/0 Q931: RX <- SETUP pd = 8 callref = 0x0077

Sending Complete

Bearer Capability and 0x8090A3 =

Standard = CCITT

Transfer Capability = Speech

Transfer Mode = Circuit

Transfer Rate = 64 kbit / s

Channel and ID = 0xA98382

Exclusive, Channel 2

Progress Ind., and = 0xA590 - Reserved value

Calling Party Number i = 0x2183,'9988 '

Plan: ISDN, Type: National

Called Party Number i = 0x89,'8888 '

Plan: Private, Type: Unknown

Shift to Codeset 5

Codeset 5 IE = 0x31 and 0x80

ISDN BR0/1/0 Q931: TX -> CALL_PROC pd = 8 callref = 0x8077

Channel and ID = 0xA98382

Exclusive, Channel 2

ISDN BR0/1/0 Q931: TX -> ALERTING pd = 8 callref = 0x8077

Facility and the 0x91AA06800100820100A11602010006052B0C028776020116300102830437313536 =

Facility and the 0x91AA06800100820100A113020100020101800B4A2E474F525A594E534B49 =

Progress Ind., and = 0x8088 - In-band info or appropriate now available

ISDN BR0/1/0 Q931: RX <- FACILITY pd = 8 callref = 0x0077

Facility and the 0x91AA0F800101A107A5050A01001200820100A406020100810101 =

ISDN BR0/1/0 Q931: RX <- DISCONNECT pd = 8 callref = 0x0077

Cause and = 0x8490 - Normal call clearing

ISDN BR0/1/0 Q931: TX -> RELEASE pd = 8 callref = 0x8077

Cause and = 0x8090 - Normal call clearing

ISDN BR0/1/0 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x0077

313
Views
0
Helpful
1
Replies