Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

Cisco Voice Gateway PRI and Nortel 81c

Has anyone used PRI-NI2 between the an Option81c and a Cisco GW? I have seen examples on CCO that use 5ESS successfully, but not NI2.

4 REPLIES
Cisco Employee

Re: Cisco Voice Gateway PRI and Nortel 81c

We ususaly do dms-100 between nortel and cisco gw. I have heard there are issue with using ni2. That was in the past I am not sure if it is still a problem. If you are using IOS gateway then make the nortel network side sl100 and cisco user side dms-100. If you are using 6608 or dt-24+ I think we can just be network side dms-100 and nortel be user side.

Hope this helps,

-Mckee

New Member

Re: Cisco Voice Gateway PRI and Nortel 81c

Here are all of my Nortel 81C configs for DMS100.

****Special Notes

FNP = Flexible Numbering Plan must be YES or 000 is

added to the number field when calling Meridian to AVVID.

TRNX = Transfer on Private Network Must be YES or will not be able to transfer calls.

EXTT = External Trunk to Trunk Must be YES or will not be able to transfer calls.

LD 15

TYPE NET_DATA

CUST 00

OPT RTD

AC2

FNP YES

ISDN YES

PINX_DN

HNPA 920

HNXX 734

HLOC

LSC

RCNT 5

OCLI NO

TRNX YES

EXTT YES

FTOP FRES

VNR NO

NIT 8

FOPT 14

****Special Notes

TKTP = TIE

DDMI = Digit Manipulation Index Does not need to be set unless you want it set here.

IFC = S100

Cisco Router should be DMS100 (This is how name/number passes).

NCNA = YES Network Calling Name Allowed

NCRD = YES Network Call Redirection Allowed

IANC = YES or NO Depending on configuration.

LD 16

TYPE RDB

CUST 00

ROUT 82

DES AVVID2

TKTP TIE

NPID_TBL_NUM 0

ESN YES

CNVT YES

DDMI 9

ATDN 2400

SAT NO

RCLS INT

DTRK YES

DGTP PRI

ISDN YES

MODE PRA

IFC S100

SBN NO

NCNA YES

NCRD YES

CHTY BCH

CTYP CDP

INAC YES

ISAR NO

CPUB OFF

DAPC YES

TBL 0

BCOT 0

DSEL 3VCE

PTYP PRI

AUTO NO

DNIS NO

DCDR NO

ICOG IAO

SRCH LIN

TRMB YES

STEP

ACOD 6672

TCPP NO

TARG 01

CLEN 1

BILN NO

OABS

INST

IDC NO

DCNO 0 *

NDNO 0

DEXT NO

ANTK

SIGO STD

ICIS YES

TIMR ICF 512

OGF 512

EOD 13952

NRD 10112

DDL 70

ODT 4096

RGV 640

GRD 896

SFB 3

NBS 2048

NBL 4096

TFD 0

PAGE 002

DRNG NO

CDR NO

MUS YES

MRT 47

RACD NO

EQAR NO

FRL 0 0

FRL 1 0

FRL 2 0

FRL 3 0

FRL 4 0

FRL 5 0

FRL 6 0

FRL 7 0

OHQ NO

OHQT 00

CBQ NO

AUTH NO

PLEV 2

ALRM NO

ART 0

SGRP 0

AACR NO

****No Special Notes Here

LD 14

TN 094 01

TYPE TIE

CDEN SD

CUST 0

TRK PRI

PDCA 1

PCML MU

NCOS 7

RTMB 82 1

B-CHANNEL SIGNALING

TGAR 0

AST NO

IAPG 0

CLS UNR DTN CND WTA LPR APN THFD HKD

P10 VNL

TKID

DATE 12 DEC 2001

****Special Notes

IFC = S100

Cisco Router should be DMS100 (This is how name/number passes).

RCAP = ND2 (Name Display Method 2) So name comes across.

SIDE = NET Must be Network because Cisco usually configs their side as USER.

LD 17

ADAN DCH 9

CTYP MSDL

GRP 2

DNUM 7

PORT 2

DES avvid

USR PRI

DCHL 94

OTBF 32

PARM RS422 DTE

DRAT 64KC

CLOK EXT

IFC S100

SIDE NET

CNEG 1

RLS ID **

RCAP ND2

T200 3

T203 10

N200 3

N201 260

K 7

LD 20

TYPE TLST

TKTP TIE

ROUT 82

DES AVVID2

TN 094 01 MBER 1 AVVID

TN 094 02 MBER 2 AVVID

TN 094 03 MBER 3 AVVID

TN 094 04 MBER 4 AVVID

TN 094 05 MBER 5 AVVID

TN 094 06 MBER 6 AVVID

TN 094 07 MBER 7 AVVID

TN 094 08 MBER 8 AVVID

TN 094 09 MBER 9 AVVID

TN 094 10 MBER 10 AVVID

TN 094 11 MBER 11 AVVID

TN 094 12 MBER 12 AVVID

TN 094 13 MBER 13 AVVID

TN 094 14 MBER 14 AVVID

TN 094 15 MBER 15 AVVID

TN 094 16 MBER 16 AVVID

TN 094 17 MBER 17 AVVID

TN 094 18 MBER 18 AVVID

TN 094 19 MBER 19 AVVID

TN 094 20 MBER 20 AVVID

TN 094 21 MBER 21 AVVID

TN 094 22 MBER 22 AVVID

TN 094 23 MBER 23 AVVID

LD 86

RLI 52

ENTR 0

LTER NO

ROUT 82

TOD 0 ON 1 ON 2 ON 3 ON

4 ON 5 ON 6 ON 7 ON

CNV NO

EXP NO

FRL 0

DMI 0

FCI 0

FSNI 0

SBOC NRR

OHQ NO

CBQ NO

ISET 0

NALT 5

MFRL 0

LD 87

DSC

DSC 2424

FLEN 4

DSP LSC

RLI 52

NPA

NXX

DSC 2499

FLEN 4

DSP LSC

RLI 52

NPA

NXX

Procedures for Setting Up an IP Phone for an Existing PBX Extension

Steps

#1. Log in to the PBX, then Print the DN you want to be an IP Phone DN in LD 20.

>ld 20

PT0000

REQ: prt

TYPE: dn

TYPE DNB

CUST 0

DN 2400

DATE

PAGE

DES

DN 2400

TYPE SL1

TN 116 0 15 04 KEY 00 H MARP DES L4DI03 27 JAN 2002

(3904)

NACT

#2. Remove the DN from every phone it appears on.

REQ: chg

TYPE: 3904

TN 116 0 15 4

ECHG yes

ITEM key 0 nul

KEY

ITEM

HNT FNA

HNT FNA

HNT FNA

#3. Add the DN in LD 87 to the Coordinated Dial Plan as a Distant Steering Code in RLI 52. Flen must be 4 unless the extension has more than 4 digits.

>ld 87

ESN000

MEM AVAIL: (U/P): 4154561 USED U P: 2801757 498401 TOT: 7454719

DISK SPACE NEEDED: 816 KBYTES

2MB BACKUP DISKETTE(S) NEEDED: 1 (PROJECTED LD43 - BKO)

REQ new

CUST 0

FEAT cdp

TYPE dsc

DSC 2400

FLEN 4

DSP

RLI 52

NPA

NXX

DSC (enter again if there are no more DNs to enter)

New Member

Re: Cisco Voice Gateway PRI and Nortel 81c

VG200 Router Config for DMS100

aalcmvg001#sh run

Building configuration...

Current configuration : 1570 bytes

!

version 12.2

no service pad

service timestamps debug uptime

service timestamps log uptime

no service password-encryption

!

hostname aalcmvg001

!

logging buffered 4096 debugging

enable password avvid

!

voice-card 1

!

ip subnet-zero

!

call rsvp-sync

isdn switch-type primary-dms100

voice rtp send-recv

!

!

!

!

!

!

controller T1 1/0

framing esf

linecode b8zs

pri-group timeslots 1-24

!

!

interface FastEthernet0/0

ip address 10.80.231.41 255.255.255.0

speed 100

full-duplex

!

interface Serial1/0:23

no ip address

no logging event link-status

isdn switch-type primary-dms100

isdn incoming-voice voice

isdn map address ^[1-9] plan unknown type unknown

isdn map address ^011 plan unknown type unknown

isdn flip-chan-flag

isdn T310 30000

no cdp enable

!

ip classless

ip route 0.0.0.0 0.0.0.0 10.80.231.1

no ip http server

ip pim bidir-enable

!

!

voice-port 1/0:23

input gain -1

output attenuation 1

echo-cancel coverage 32

no comfort-noise

!

dial-peer voice 9 pots

destination-pattern 9

progress_ind alert enable 8

progress_ind progress enable 8

progress_ind connect enable 8

direct-inward-dial

port 1/0:23

!

dial-peer voice 1 voip

preference 10

destination-pattern .T

progress_ind setup enable 3

session target ipv4:10.80.231.31

dtmf-relay h245-alphanumeric

codec g711ulaw

no vad

!

dial-peer voice 2000 voip

destination-pattern 2...

progress_ind setup enable 3

session target ipv4:10.80.231.31

dtmf-relay cisco-rtp h245-signal h245-alphanumeric

codec g711ulaw

no vad

!

!

line con 0

line aux 0

line vty 0 4

password avvid

login

!

end

aalcmvg001#

Blue

Re: Cisco Voice Gateway PRI and Nortel 81c

Yes, I am running PRI-NI2 between a 81C and a 3640 GW running MGCP with backhaul. Works fine, no issues yet, but have only had it set up in a lab environment for a few days.

702
Views
0
Helpful
4
Replies
CreatePlease to create content