10-30-2014 12:54 AM - edited 03-13-2019 08:42 PM
Hi,
Can anyone help, i have new 2901 router and i cannot create VOIP dial-peer, Only i can see the option of POTS.
Below is the IOS version.
c2900-universalk9-mz.SPA.152-4.M4.bin
10-30-2014 12:59 AM
Hi Khan,
can u share the show licesne feature and show license detail from Router?
also, share show inventory
regds,
aman
10-30-2014 01:05 AM
Hi Aman,
Below is the infomation
Index 1 Feature: ipbasek9
Period left: Life time
License Type: Permanent
License State: Active, In Use
License Count: Non-Counted
License Priority: Medium
Index 2 Feature: securityk9
Period left: Not Activated
Period Used: 0 minute 0 second
License Type: EvalRightToUse
License State: Not in Use, EULA not accepted
License Count: Non-Counted
License Priority: None
Index 3 Feature: uck9
Period left: Life time
License Type: Permanent
License State: Active, In Use
License Count: Non-Counted
License Priority: Medium
Index 4 Feature: datak9
Period left: Not Activated
Period Used: 0 minute 0 second
License Type: EvalRightToUse
License State: Not in Use, EULA not accepted
License Count: Non-Counted
License Priority: None
Index 5 Feature: gatekeeper
Period left: Not Activated
Period Used: 0 minute 0 second
License Type: EvalRightToUse
License State: Not in Use, EULA not accepted
License Count: Non-Counted
License Priority: None
Index 6 Feature: SSL_VPN
Period left: Not Activated
Period Used: 0 minute 0 second
License Type: EvalRightToUse
License State: Not in Use, EULA not accepted
License Count: 0/0 (In-use/Violation)
License Priority: None
Index 7 Feature: ios-ips-update
Period left: Not Activated
Period Used: 0 minute 0 second
License Type: EvalRightToUse
License State: Not in Use, EULA not accepted
License Count: Non-Counted
License Priority: None
Index 8 Feature: SNASw
Period left: Not Activated
Period Used: 0 minute 0 second
License Type: EvalRightToUse
License State: Not in Use, EULA not accepted
License Count: Non-Counted
License Priority: None
Index 9 Feature: hseck9
Index 10 Feature: cme-srst
Period left: Not Activated
Period Used: 0 minute 0 second
License Type: EvalRightToUse
License State: Not in Use, EULA not accepted
License Count: 0/0 (In-use/Violation)
License Priority: None
Index 11 Feature: WAAS_Express
Period left: Not Activated
Period Used: 0 minute 0 second
License Type: EvalRightToUse
License State: Not in Use, EULA not accepted
License Count: Non-Counted
License Priority: None
Index 12 Feature: UCVideo
Period left: Not Activated
Period Used: 0 minute 0 second
License Type: EvalRightToUse
License State: Not in Use, EULA not accepted
License Count: Non-Counted
License Priority: None
NAME: "CISCO2901/K9", DESCR: "CISCO2901/K9 chassis, Hw Serial#: , Hw Revision: 1.0"
PID: CISCO2901/K9 , VID: V06 , SN:
NAME: "2nd generation four port FXO voice interface daughtercard on Slot 0 SubSlot 0", DESCR: "2nd generation four port FXO voice interface daughtercard"
PID: VIC2-4FXO , VID: V03 , SN:
NAME: "2nd generation four port FXO voice interface daughtercard on Slot 0 SubSlot 1", DESCR: "2nd generation four port FXO voice interface daughtercard"
PID: VIC2-4FXO= , VID: V , SN:
NAME: "PVDM3 DSP DIMM with 16 Channels on Slot 0 SubSlot 4", DESCR: "PVDM3 DSP DIMM with 16 Channels"
PID: PVDM3-16 , VID: V01 , SN:
NAME: "C1941/C2901 AC Power Supply", DESCR: "C1941/C2901 AC Power Supply"
PID: PWR-1941-2901-AC , VID: , SN:
10-30-2014 01:12 AM
Hi,
I can see Voice licenses are OK.
what is the exact error message u get and is it on H.323/MGCP ?
what is configuration u are doing in Call manager ?
regds,
aman
10-30-2014 01:38 AM
When i create VOIP dial peer i cannot.
dial-peer voice 1 pots, in the same way when i create dial-peer voice 2 voip it says unrecognized command. When i press ? after dial-peer voice 2 ? it shows only pots not VOIP.
I am using H323 Gateway, in CUCM server i just added a new H323 gateway.
Thanks.
10-30-2014 01:49 AM
I think you are using MGCP . In this, all the dial plan configuration is handled by Call Manager and u just need to enable POTS dial peer in GW for communication with Call Manager.
regds,
aman
10-30-2014 02:27 AM
Hi,
I am not using MGCP, by default these command should be available, but its not.
10-30-2014 03:20 AM
Can u explain the setup?
Are u connecting router to a EPABX ?
Lastly, is Call Manager being integrated to VG? If not MGCP, then , command should come.
regds,
aman
11-02-2014 11:23 PM
Hi.
Even if there would be MGCP, creating a VOIP dial-peer would be possible, regardless of MGCP used or not.
Can you do a sho run for us and post it to here (as an attachment, please).
G.
11-03-2014 01:55 AM
Hi,
I tried the same command in same router model and version , it works.
can u share the output while conifiguring
router(config)#dial-peer voice 10 ?
regds,
aman
11-03-2014 09:20 PM
Hi,
I know these commands should work by default.
router(config)#dial-peer voice 10 it shows only pots, no VOIP. I dont have access to router as its in remote location. Any other suggestions ?
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: