10-01-2006 05:29 AM - last edited on 03-25-2019 06:53 PM by ciscomoderator
Hi all,
we are using a gateway (using qsig) to connect to a BOSCH 33XE PBX.
Everything works fine, only names from callmanager are not shown at the PBX phones, while PBX-user names are shown at the IP phones.
I did a "debug isdn q931" to have a look and I saw a calling number, but no calling name (calling from callmanager to PBX).
Any ideas?
Axel
p.s. I checked the route pattern and the gateway setting belonging calling name restriction: nothing.
10-01-2006 10:06 AM
Hi Axel,
Which Q.SIG variant you are using to connect to the PBX? 0x9F (ISO) or 0x91 (ECMA)
In Cisco CallManager you may want to check those values under:
CCMAdmin | Service | Service Parameters | Cisco CallManager | Click Advanced
ASN.1 ROSE OID Encoding*
QSIG Variant*
You may want to match these parameters to your PBX.
10-02-2006 12:07 AM
I tried both variants (but read, that calling name is part of qsig basic) with same result.
Here is a part of the debug:
4w1d: Modify Nominator =
4w1d: DTMF_TONE_DET
4w1d: Modify Nominator =
4w1d: MODEM
4w1d: CODEC_BYTES
4w1d: NTE_PAYLOAD
4w1d: DTMF_RELAY
4w1d: NSE_PAYLOAD
4w1d: SIGNAL_TYPE
4w1d: FAX_BYTES
4w1d: NTE_TX_PAYLOAD
4w1d: SEQ_NUM_START
4w1d: MP_CAP_MODEM_PROTO
4w1d: MP_CAP_MODEM_CODEC
4w1d: MP_CAP_VOICE_RTP_NSE_PAYLOAD
4w1d: MR_INFO
4w1d: Modify Nominator =
4w1d: FAX_TONE_DET
4w1d: MODEM_TONE_DET
4w1d: CM_TONE_DET
4w1d: ISDN Se0/0:15 Q931: TX -> SETUP pd = 8 callref = 0x0041
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA9839F
Exclusive, Channel 31
Facility i = 0x91AA06800100820100A11602010106042B0C0900800B542E20536368756C756E67
Calling Party Number i = 0x0081, '8834999'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '8'
...
Kind regards
Axel
10-02-2006 06:34 AM
Hi Axel,
Per the last debug 0x91 in CCM, you are using ECMA variant, make sure that under CCM Service Parameters ASN.1 ROSE OID Encoding* is set to ECMA also, those values should match in the PBX side.
If that is the case, please upload the detailed CCM trace.
Thanks
//G
10-03-2006 10:43 PM
Hi //G,
thanks for you help. It is a productive system, so I am not able to post ccm traces here.
I will open a Service Request.
Kind regards
Axel
10-18-2006 09:05 AM
Transform this Hex string:
Facility i = 0x91AA06800100820100A11602010106042B0C0900800B542E20536368756C756E67
to ASCII (e.g. http://www.yellowpipe.com/yis/tools/encrypter/index.php)
and you receive the send displayname.
Axel
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide