Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

CME 3.3 and Translation Rules Config?

Hi.

I already have a CME site up and running using a T1 E&M-WINK to access the PSTN. All the DNs are in the range of 1400-1499. There are H323 connections to other sites (i.e. not running cme at the moment) around 30 sites with legacy PBX connected to cisco routers.

In order to reach the CME site people from other sites dial [Access-Code]14 (i.e. 14 is the site number). When that call hits the cme router I need to ring the pilot number for the site that is configured to ring on all IP Phones at the moment. I tried creating a dial-peer voip with destination-pattern of 14 and in it I configured a translation rule to convert the digits to the pilot number.. But when I did that.. all communication between IP Phones at the CME site is broken because they can't dial each other... because of the overlapping destination-patter..

Any other way to make this work?

Thanks in advanced,

-Jose

6 REPLIES
New Member

Re: CME 3.3 and Translation Rules Config?

Can you create a dial peer and a outgoing translation rule on the remote routers. Change the number before it hits the CME.

http://www.cisco.com/univercd/cc/td/doc/product/software/ios123/123cgcr/vvfax_c/int_c/dpeer_c/dp_confg.htm

Dan

New Member

Re: CME 3.3 and Translation Rules Config?

That would be a good way to do it.. however there are more than 30 sites... and the client don't want to go to every router and do the changes.. this is the first cme site they are implementing.. and they would like the behavior to be the same without changing configs on the other sites... so somehow I need to do the translation on the cme ...

-Jose

New Member

Re: CME 3.3 and Translation Rules Config?

OK, good point. I am confused on what is being done with the number. Are the people at the remote site trying to reach a certain person at the CME site, or a group of extensions. What is this pilot number and what is it used for?

Help me understand the call flow.

Dan

New Member

Re: CME 3.3 and Translation Rules Config?

Ok let me explain better..

There are 30 sites with legacy pbx at the moment that are connected to voip gateways in order to do toll-by-pass calls. People on all sites dial a code and then the number of the site... When the calls reach the final destination the legacy pbx ring an specific extension.

Now one of the sites has a CME VoIP Router that replaced their legacy pbx. I know that all other sites now can dial the extensions directly but because all users are not notified yet.. all other sites will still be calling with the code+ [store-number].. when the [store-number] gets to the CME router I need to convert that number to a valid Directory Number and/or a Hunt-Group, etc..

Any ideas?

New Member

Re: CME 3.3 and Translation Rules Config?

This is theoretical and I would need to lab it up tomorrow. What about creating a dial peer on the CME with incoming called-number 14 and translate it there.

Here is a website that might help.

http://www.cisco.com/en/US/tech/tk652/tk90/technologies_tech_note09186a008010fed1.shtml

Dan

New Member

Re: CME 3.3 and Translation Rules Config?

I think I got it to work. Try this config on the CME:

!

voice translation-rule 1

rule 1 /814/ /1499/

!

voice translation-profile Test

translate called 1

!

dial-peer voice 1 pots

translation-profile incoming Test

incoming called-number 814

direct-inward-dial

!

Let me know how it works.

Dan

134
Views
0
Helpful
6
Replies