Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

CME 9.0 SIP IP Phone 8945/9971 video conference

Dear expert,

Does anybody know any issues against video multi-party conference(ad-hoc and meetme) among SIP IP Phone 8945 (2 sets) and a 9971 on CME9.0?

(To be sure, P-to-P video call is fine by using SIP IP Phone)

Moreover, meetme voice conference is also available for SIP IP Phone 8945/9971 by using dspfarm settings of PVDM-3.

However, only video conference of ad-hoc and meetme does not work.

Are there any specific configuration on this?

Appreciate your advice.

Thanks & Regards,

Iizuka

Everyone's tags (4)
6 REPLIES
Blue

CME 9.0 SIP IP Phone 8945/9971 video conference

Hi

CME 9.0 and 99XX and 89XX phone does supports Video conefence. Plese send us config and let see what is wrong with it.

Regards

Ronak Patel

Rate helpful posts.

Regards Ronak Patel Rate all helpful post by clicking stars below the answer.
New Member

Re: CME 9.0 SIP IP Phone 8945/9971 video conference

Hi Ronak,

Thank you for your reply.

I attached the file (config-20120614.txt) of my configuration.

I really appreciate if you could advise on this.

Thanks & regards,

Iizuka

Blue

Re: CME 9.0 SIP IP Phone 8945/9971 video conference

HI

Any specific reason to create two cm group. Put both audio and video conference in same ccm group and test.

sccp ccm group 2

associate ccm 1 priority 1

associate profile 2 register videoconf

!

sccp ccm group 1

associate ccm 1 priority 2

associate profile 1 register meetmeconf001

!

Regards

Ronak Patel

Rate helpful posts by clicking stars below the answer.

Regards Ronak Patel Rate all helpful post by clicking stars below the answer.
New Member

Re: CME 9.0 SIP IP Phone 8945/9971 video conference

Hi Ronak,

Thank you for your comments.

I already tried to test by using same group for both of audio and video conference.

But, I got same incident.

Also, we can use video homogeous of profile for SIP 9971 and 8945. I am not sure the reasion why we need to use heterogeneous profile.

Because, both os 9971 and 8945 will use VGA 30fps.

Are there any other point to fix this issue?

Appreciate you help!!

Thanks & Regards,

Iizuka

Blue

Re: CME 9.0 SIP IP Phone 8945/9971 video conference

HI

heterogeneous is not required, that is why the comment is removed as I thought you are running multiple phones.

You config looks good.  If you phones are having other firmware please upgrade to 9.2.2 and see if it get resolved. As per config you are running correct firmware, but just in case if phone are not upgraded to correct firmware please upgrade it and issume may get resloved.

Regards

Ronak Patel

Rate helpful posts by clicking stars below the answer.

Regards Ronak Patel Rate all helpful post by clicking stars below the answer.
New Member

Re: CME 9.0 SIP IP Phone 8945/9971 video conference

Hi Ronak,

Active load of 8945 is sip 9-2-2-0.

Active load of 9971 is sip9971.9-2-2SR1-9.

Firmware should be OK.

Both of active loads is latest version for CME.

Thanks & Regards,

Iizuka

3029
Views
0
Helpful
6
Replies