Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

Communication with ATA´s 186

Hi, somebody knows how can i communicate two ATA´s 186 ?

Later, what do i need for having more than two ?

Thanks

4 REPLIES
Community Member

Re: Communication with ATA´s 186

What are you trying to do with them? Justtrying to get them intially setup?

Brian

Community Member

Re: Communication with ATA´s 186

I want to talk between them, yes i just trying to get initially setup.

Luis

Community Member

Re: Communication with ATA´s 186

This link should help you out in setting up the ATA device's

http://www.cisco.com/en/US/products/hw/gatecont/ps514/products_administration_guide_chapter09186a00800c4d1a.html

To get to the web interface of the device:

Step 1 Connect an analog touch-tone phone to the port labeled Phone 1 on the back of the Cisco ATA.

Step 2 Lift the handset and press the function button located on the top of the Cisco ATA. You should receive the initial voice configuration menu voice prompt.

Step 3 Using the telephone keypad, enter the voice menu code for the parameter that you want to configure or the command that you want to execute, then press #. For a list of voice menu codes, see "Voice Menu Codes."

Use these menu codes

Table B-1 Cisco ATA Voice Menu Codes—Information Options

Option Voice Menu Code Description

Build information

123123

Build date of the Cisco ATA software

Review IP address

21

Returns IP address of the Cisco ATA

Review MAC address

24

Returns media access control (MAC) address of the Cisco ATA

Review network route IP address

22

Returns IP address of the network route

Review subnet mask

23

Returns subnet mask of the network route

Version number

123

Returns version number of the Cisco ATA software

Table B-2 lists configuration codes. For additional information about these parameters, see ""Parameters and Defaults."

Table B-2 Cisco ATA Voice Menu Codes—Configuration Parameters

Option Voice Menu Code Description

Audio mode

312

Allows finer control of the audio component to suit certain user applications

Caller ID method

316

Specifies the signal format when generating the Caller ID format to use

Connection mode

311

Controls the connection mode of the call signaling protocol

Dynamic Host Configuration Protocol (DHCP)

20

Controls whether the Cisco ATA can automatically obtain configuration parameters from a server over the network

DNS 1 IP

916

IP address of the primary DNS server

DNS 2 IP

917

IP address of the secondary DNS server

Encrypt key

320

Encrypts the configuration file on the TFTP server

Num Tx frames

35

Number of frames transmitted per packet

Static IP address

1

IP address of the Cisco ATA

LBR codec

300

Low-bit-rate codec selection

Media port

202

Specifies which base port the Cisco ATA uses to receive RTP media streams

Static network route address

2

Network router address

NPrintf address

81

IP address of a host to which all Cisco ATA debug messages are sent

Set password

7387277

Configuration interface password

Signal timers

318

Timeout values controlling the starting or stopping of a signaling event

MGCP protocol

38

Selects the signaling protocol

Static subnet mask

10

Specifies the subnet mask for the Cisco ATA

TFTP URL

905

When TFTP configuration is used, IP address of the TFTP server

UDP TOS bits

255

Determines the precedence and delay of UDP IP packets

Use TFTP

305

Enables TFTP as configuration method

Table B-3 lists codes used in the software upgrade process. For information about these codes, see "Appendix , "Upgrading the Cisco ATA Signaling Image."

Table B-3 Cisco ATA Voice Menu Codes—Software Upgrade

Option Voice Menu Code Description

Upgrade software

100

Used in the software process to enter the IP address of the PC

Upgrade language to English

101

When upgrading software, changes or upgrades the voice prompt language to English

Guest Search:

Site To SearchSearch All Cisco.comProducts & ServicesCisco Voice GatewaysCisco ATA 180 Series A...

Community Member

Re: Communication with ATA´s 186

Hi, , i don´t have problem connecting to the ATA´s,

I have seen the web configuration, but i don´t understand some commands for getting communication between them.

Luis

95
Views
0
Helpful
4
Replies
CreatePlease to create content