Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

Dear Expert,VG224 problem about hook-flash transfer call

dear all

i have setup VG224 hookflash for call transfer,but not work

my analog phone have identify it support 130 ms for call transfer buttom

pls kindly advise the example config

tks again

10 REPLIES
New Member

Re: Dear Expert,VG224 problem about hook-flash transfer call

New Member

Re: Dear Expert,VG224 problem about hook-flash transfer call

Check this bug

CSCeg42217: No dial-tone on hookflash if on-hold

Symptoms: Involves two parities (A and B in this example) who are in conversation. When A does a hook flash and tries to transfer the phone to the transfer target C, A will hear the dial tone indicating that A can dial an extension and connect to transfer target. In the mean time, B is put "on-hold" so that B's call is terminated but the call is still connected.

At this time, we block the hook flash handling. This will disallow the side that is put on hold (which is party B in our case) to make a transfer. This is to stop the chain of uncertainty if the party that is on hold wants to make a transfer.

Conditions: This is only applicable on the analog skinny endpoint connecting to Cisco CME and only affects the Cisco VG 224. No command-line interface (CLI) is involved.

Workaround: There is no workaround.

http://www.cisco.com/en/US/products/sw/voicesw/ps556/prod_release_note09186a008041df56.html

New Member

Re: Dear Expert,VG224 problem about hook-flash transfer call

in my case phone a push flash buttom

it doesn't work

phone b will not hold

and phone a not appear dial tone

phone a and phone b still connect

tks

so i think it may hook-flash parameter problem

very tks

New Member

Re: Dear Expert,VG224 problem about hook-flash transfer call

analog phone flash key frequency (can adjust)

earth

130 ms

260 ms

600 ms

New Member

Re: Dear Expert,VG224 problem about hook-flash transfer call

Hi Jason. That's my case too...

I've tried many timing configurations and replaced the analog phone. Still looking for an answer.

Silver

Re: Dear Expert,VG224 problem about hook-flash transfer call

Did you try to configure the max and min flash timer on the voice-ports?

voice-port 2/0

timing hookflash-in 140 120

or perhaps even 150 110 as max and min value

Problem with hookflash is that it is never exactly 130ms, especially not with the cheap ... phones

HTH,

Leo

New Member

Re: Dear Expert,VG224 problem about hook-flash transfer call

I've found an answer for that on this forum!

I had to set "Maximun Number of Calls" on the device in CCM to 2 calls.

It worked this way:

- receive a call on VG extention;

- press flash, get a new line;

- call second extention;

- hook the fone;

The call is trasfered to the second call.

I had to configure stcapp correctly and activate call control feature.

I hope it help you Jason.

Silver

Re: Dear Expert,VG224 problem about hook-flash transfer call

Hi,

Don't know if you had your problem resolved yet, but I ran into the same issue today (my first VG224 install) and found the simple solution.

Just configure the minimum and maximum hookflash timer under the voice-port in a way that it matches your hookflash time.

I have a hookflash of 100ms and had to configure this:

voice-port 2/0

cptone BE

timing hookflash-in 110 90

in your case it would be something like:

timing hookflash-in 140 120

Hope it helps,

Leo

Silver

Re: Dear Expert,VG224 problem about hook-flash transfer call

Is it sccp or h323? With SCCP, it could be simply changing the busy trigger/maximum calls on the callmanger from 1 (default) to 2 so the phone could open an additional line for transfer

New Member

Re: Dear Expert,VG224 problem about hook-flash transfer call

Hi,

I've the same problems with Max. Calls set to 2 on CUCM 5.1.2.

Is there any workaround?

2867
Views
0
Helpful
10
Replies
CreatePlease to create content