Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Dial-peer matching question and sho dial-peer voice sum

Hi - I have two questions that may be related to each other. I have a router with 6 inbound POTS lines and I want to match a single incoming POTS peer to route all calls to the onboard IOS/TCL/AA script service.

I'd like to have a single POTS peer match for all incoming calls to hit the IOS/TCL/AA:

dial-peer voice 5000 pots

service siteaa

incoming called-number 5000

However, there is no match until I put a voice port specified on the dial-peer.

dial-peer voice 5000 pots

service siteaa

incoming called-number 5000

port 2/0/8

The analog port is defined as such:

voice-port 2/0/8

timeouts interdigit 3

connection plar opx 5000

So do I need to define 6 POTS peers - each with one analog port defined - in order to send all calls to the IOS/TCL/AA service?

Also, when I show the POTS peer, this is what I get:

C2821-TestRouter-HQ(config-dial-peer)#do sh dial-peer voice sum

dial-peer hunt 0

AD PRE PASS OUT

TAG TYPE MIN OPER PREFIX DEST-PATTERN FER THRU SESS-TARGET STAT

PORT

5000 pots up up 0 down

2/0/8

What is the OUT/STAT column in SHO DIAL-PEER VOICE SUMMARY? It shows "down" in this case.

Thanks.

3 REPLIES

Re: Dial-peer matching question and sho dial-peer voice sum

A dial-peers operational status is down unless you specify the port command. I havent tested this personally with multiple dial-peers but i would think, all you would need would be to specify one dial-peer with one of the ports. Worth giving it a try!!

New Member

Re: Dial-peer matching question and sho dial-peer voice sum

Thanks, Shanky. Not to contradict, but check out this URL:

http://www.cisco.com/en/US/customer/tech/tk652/tk90/technologies_tech_note09186a008010e6d1.shtml

This says that a dial-peer is operationally up with only the incoming called-number specified without a port. However, if it is destination-pattern, then yes you need a port (POTS) or target (VoIP). If you look closely at the SHO DIAL-PEER VOICE SUMMARY, it does show operationally up - but there is a new column (12.4 mainline) - at the very end - that is OUT/STAT. Thid doesn't appear to be the operational status.

Any comments are appreciated.

Re: Dial-peer matching question and sho dial-peer voice sum

Kyle,

you are right. i was wrong abt the op. status.

The 12.4 voice command reference guide doesnt ttell any abt what that field means.

Since this is an fxo, i think this is what you should do.

-----Edited-----------

voice service voip

allow-connections h323 to h323

---------------------

voice-port 1/0

connection plar 5000

dial-peer voice 1 pots

incoming called-number . -- this is to match any inbound call, regardless of port.

int lo 0

ip add 1.1.1.1 255.255.255.255

dial-peer voice 2 voip

incoming called-number 5000

service site1aa

codec g711ulaw

no vad

dial-peer voice 3 voip

destination-pattern 5000

session target ipv4:1.1.1.1

codec g711ulaw

no vad

HTH

Sankar

PS: please remember to rate posts!

561
Views
5
Helpful
3
Replies