Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Dialers from the outside hear the dial tone

Our gateway is connected to the PSTN with a PRI line. Eveything works fine from the inside. We can call outside but when the outside calls us from these line they hear a dial-tone. Why can this happen?

1 ACCEPTED SOLUTION

Accepted Solutions

Re: Dialers from the outside hear the dial tone

A key concept is that a single phone call through a voice gateway has two call legs, one inbound and one outbound, and each leg matches a dial-peer.

Outbound are the easiest to understand because they operate alot like route statements do to the IP data world; they tell the call/packet where to go. But inbound are important, too, because they instruct the VG on how to receive calls. Alot of VG get by using the (hidden) default dial-peer to match incoming calls, but in some cases, like yours, certain commands must be specified.

The "incoming called-number ." command is used to match the incoming calls to that dial-peer. The 'direct-inward-dial' command *should* eliminate that dialtone your caller hear. And these need to be applied to a pots dial-peer because the incoming call is coming in on a POTS pri.

8 REPLIES
Hall of Fame Super Gold

Re: Dialers from the outside hear the dial tone

Configure:

dial-peer voice 1 pots

incoming called-number .

direct-inward-dial

After that, you will begin dealing with the number of DID digits sent to CM, translations, etc.

Re: Dialers from the outside hear the dial tone

incoming called-number .

direct-inward-dial

check this is there....

New Member

Re: Dialers from the outside hear the dial tone

sorry but we cant write this on voip dial-peer. Our calls comes from pri line and should go to the voip dial-peer.

Re: Dialers from the outside hear the dial tone

This is a pots command:

dial-p v 1 pots

direct

incoming called .

Re: Dialers from the outside hear the dial tone

A key concept is that a single phone call through a voice gateway has two call legs, one inbound and one outbound, and each leg matches a dial-peer.

Outbound are the easiest to understand because they operate alot like route statements do to the IP data world; they tell the call/packet where to go. But inbound are important, too, because they instruct the VG on how to receive calls. Alot of VG get by using the (hidden) default dial-peer to match incoming calls, but in some cases, like yours, certain commands must be specified.

The "incoming called-number ." command is used to match the incoming calls to that dial-peer. The 'direct-inward-dial' command *should* eliminate that dialtone your caller hear. And these need to be applied to a pots dial-peer because the incoming call is coming in on a POTS pri.

New Member

Re: Dialers from the outside hear the dial tone

My debug ccapi and it says incoming dial-peer 0 but there is no dial-peer 0...

Incoming Dial-peer=0, Progress Indication=NULL(0), Calling IE Present=TRUE,

Source Trkgrp Route Label=DIGER, Target Trkgrp Route Label=, CLID Transparent=FALSE), Call Id=-1

Re: Dialers from the outside hear the dial tone

Dial-peer 0 is the hidden dial-peer that I mentioned. I'm not sure if you can modify it. I have always specified my own dial-peer for incoming calls.

New Member

Re: Dialers from the outside hear the dial tone

I created a dial-peer

dial-peer voice 66 pots

incoming called-number .

direct-inward-dial

Now incoming is coming from here and it solved the problem...

203
Views
4
Helpful
8
Replies