Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

DSP calculation question

Hello,

I have one PVDM2-32 (2 DSPs c5510 on the plane) on the board of 2821 ISR.

Under voice card I prefer to use high complexity, i.e. 6 channel per DSP (12 channels in total).

While I'm configuring PRI using 10 TS, router claims:

{

(config-controller)#pri-group timeslots 1-10

% Not enough DSP resources available to configure pri-group on controller E1 0/1/0

% The remaining dsp resources are enough for 8 time slots.

% For current codec complexity, 1 extra dsp(s) are required to create this voice port.

}

What is the reason ? Attaching 'sh voice dsp det' below.

{

#sh voice dsp detailed

DSP DSP DSPWARE CURR BOOT PAK TX/RX

TYPE NUM CH CODEC VERSION STATE STATE RST AI VOICEPORT TS ABORT PACK COUNT

==== === == ======== ======= ===== ======= === == ========= == ===== ============

----------------------------FLEX VOICE CARD 0 ------------------------------

*DSP VOICE CHANNELS*

CURR STATE : (busy)inuse (b-out)busy out (bpend)busyout pending

LEGEND : (bad)bad (shut)shutdown (dpend)download pending

DSP DSP DSPWARE CURR BOOT PAK TX/RX

TYPE NUM CH CODEC VERSION STATE STATE RST AI VOICEPORT TS ABRT PACK COUNT

===== === == ========= ======= ===== ======= === == ========= == ==== ============

C5510 001 01 None 8.4.0 idle idle 0 0 0 0/0

C5510 001 02 None 8.4.0 idle idle 0 0 0 0/0

C5510 001 03 None 8.4.0 idle idle 0 0 0 0/0

C5510 001 04 None 8.4.0 idle idle 0 0 0 0/0

C5510 001 05 None 8.4.0 idle idle 0 0 0 0/0

C5510 001 06 None 8.4.0 idle idle 0 0 0 0/0

C5510 002 01 None 8.4.0 idle idle 0 0 0 0/0

C5510 002 02 None 8.4.0 idle idle 0 0 0 0/0

C5510 002 03 None 8.4.0 idle idle 0 0 0 0/0

C5510 002 04 None 8.4.0 idle idle 0 0 0 0/0

C5510 002 05 None 8.4.0 idle idle 0 0 0 0/0

C5510 002 06 None 8.4.0 idle idle 0 0 0 0/0

*DSP SIGNALING CHANNELS*

DSP DSP DSPWARE CURR BOOT PAK TX/RX

TYPE NUM CH CODEC VERSION STATE STATE RST AI VOICEPORT TS ABRT PACK COUNT

===== === == ========= ======= ===== ======= === == ========= == ==== ============

C5510 002 01 {high} 8.4.0 alloc idle 0 0 0/2/0 02 0 15/0

C5510 002 02 {high} 8.4.0 alloc idle 0 0 0/2/1 02 0 15/0

C5510 002 03 {high} 8.4.0 alloc idle 0 0 0/3/0 02 0 36/0

C5510 002 04 {high} 8.4.0 alloc idle 0 0 0/3/1 06 0 36/0

------------------------END OF FLEX VOICE CARD 0 ----------------------------

}

  • Other Collaboration Voice and Video Subjects
3 REPLIES
New Member

Re: DSP calculation question

I've got an idea: am I right if suggest, that 4 channels are occupied by fxs/fxo assignements ?

New Member

Re: DSP calculation question

PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC

============== == ============ ===== ==== ======== ======== ==

0/2/0 -- fxs-ls up dorm on-hook idle y

0/2/1 -- fxs-ls up dorm on-hook idle y

0/3/0 -- fxo-ls up dorm idle on-hook y

0/3/1 -- fxo-ls up dorm idle on-hook y

Blue

Re: DSP calculation question

The router is showing you correctly.

You have enough DSP resources for only 8 channels.

You must have enough DSPs to support 10 channels. This would require 3 DSPs in your case for 10 g711 channels.

(4 channels per DSP in g711 for c5510 type DSPs)

(g711 because the telco is sending you g711 voice calls)

Please see the following link for the DSP Calulator to help identify what your hardware can support and how many DSPs you need to meet your requirements:

http://www.cisco.com/cgi-bin/Support/DSP/dsp-calc.pl

(requires cco login which is free to register for)

450
Views
2
Helpful
3
Replies