Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

Gw 2821 & Unavailable Controllers E1

Guys,

I wonder, what can be the cause the router

- does not show controller 0/1/0 & 0/1/1 in running-config

- consequently it does not allow to 'conf t | controller e1 0/1/0'

What can be the problem ? Thanks.

---

{ *** Related Information ***

#sh ver

Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(9)T, RELEASE SOFTWARE (fc1)

ROM: System Bootstrap, Version 12.4(1r) [hqluong 1r], RELEASE SOFTWARE (fc1)

R1 uptime is 16 minutes

System returned to ROM by power-on

System restarted at 10:59:42 UTC Tue Apr 8 2008

System image file is "flash:c2800nm-advipservicesk9-mz.124-9.T.bin"

Cisco 2821 (revision 53.50) with 247808K/14336K bytes of memory.

Processor board ID FCZ1014700H

2 Gigabit Ethernet interfaces

2 Low-speed serial(sync/async) interfaces

2 Channelized (E1 or T1)/PRI ports

1 Virtual Private Network (VPN) Module

2 Voice FXO interfaces

2 Voice FXS interfaces

DRAM configuration is 64 bits wide with parity enabled.

239K bytes of non-volatile configuration memory.

62720K bytes of ATA CompactFlash (Read/Write)

#sh diag

Slot 0:

C2821 Motherboard with 2GE and integrated VPN Port adapter, 2 ports

Port adapter is analyzed

Port adapter insertion time unknown

Onboard VPN : v2.2.0

EEPROM contents at hardware discovery:

PCB Serial Number : FOC101117EG

Hardware Revision : 1.0

Top Assy. Part Number : 800-26921-01

Board Revision : A0

Deviation Number : 0

Fab Version : 03

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Processor type : 87

Hardware date code : 20060316

Chassis Serial Number : FCZ1014700H

Chassis MAC Address : 0017.5a66.9790

MAC Address block size : 32

CLEI Code : CNMJ6P0BRB

Product (FRU) Number : CISCO2821

Part Number : 73-8853-03

Version Identifier : V02

EEPROM format version 4

PVDM Slot 0:

32-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card

Hardware Revision : 3.2

Part Number : 73-8539-04

Board Revision : A0

Deviation Number : 0

Fab Version : 03

PCB Serial Number : FOC10103G0J

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Processor type : 00

Product (FRU) Number : PVDM2-32

Version Identifier : NA

EEPROM format version 4

WIC Slot 1:

VWIC2-2MFT-G703 - 2-Port RJ-48 Multiflex Trunk - T1/E1 & G.703

Hardware Revision : 0.0

Top Assy. Part Number : 800-24920-04

Board Revision : C0

Deviation Number : 0

Fab Version : 04

PCB Serial Number : FOC10140L6F

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Product (FRU) Number : VWIC2-2MFT-G703

Version Identifier : V01

EEPROM format version 4

#sh controllers e1

#

}

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Gold

Re: Gw 2821 & Unavailable Controllers E1

Please configure:

card type e1 1

And the controllers will appear.

Note your IOS is not updated an can present many bugs.

Hope this helps, please rate post if it does!

3 REPLIES
Hall of Fame Super Gold

Re: Gw 2821 & Unavailable Controllers E1

Please configure:

card type e1 1

And the controllers will appear.

Note your IOS is not updated an can present many bugs.

Hope this helps, please rate post if it does!

Community Member

Re: Gw 2821 & Unavailable Controllers E1

Thanks, Paolo. Bull's-eye advice.

Conf mode 'card type e1 0 1' reveal interfaces.

Hall of Fame Super Gold

Re: Gw 2821 & Unavailable Controllers E1

It happens to everyone that configure a vwic2 the very first time.

Thanks for the nice rating and good luck!

206
Views
4
Helpful
3
Replies
CreatePlease to create content