04-16-2002 03:31 PM - edited 03-12-2019 03:09 PM
Could someone post an h323 gateway config preferably one that is accepting DID. thanks.
04-16-2002 04:04 PM
This is my config 3640 12.2(7a) pri connection- call manager 3.1
we have did's in the 6xxx -7960 phones- do i need dtmf-relay h245-alphnumeric ?
any obvious changes you can suggest are welcomed
User Access Verification
Password:
VoiceGW>en
Password:
CTI-VoiceGW#sh run
Building configuration...
Current configuration : 1625 bytes
!
version 12.2
no parser cache
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname VoiceGW
!
boot system flash:c3640-is-mz.122-7a.bin
enable password
!
voice-card 1
!
ip subnet-zero
!
!
no ip domain-lookup
!
isdn switch-type primary-5ess
call rsvp-sync
!
voice service pots
!
!
!
!
!
!
controller T1 1/0
framing esf
linecode b8zs
cablelength short 133
pri-group timeslots 1-24
!
!
!
interface FastEthernet0/0
ip address 192.168.1.235 255.255.255.0
duplex auto
speed auto
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface Serial1/0:23
no ip address
no logging event link-status
isdn switch-type primary-5ess
isdn incoming-voice voice
no cdp enable
!
no ip classless
ip route 0.0.0.0 0.0.0.0 192.9.250.254
ip route 0.0.0.0 0.0.0.0 192.168.1.1
ip route 192.9.250.0 255.255.255.0 192.168.1.100
ip route 192.168.1.0 255.255.255.0 192.9.250.254
no ip http server
ip pim bidir-enable
!
!
voice-port 1/0:23
!
voice-port 2/0/0
!
voice-port 2/0/1
!
voice-port 2/1/0
caller-id enable
signal groundStart
!
voice-port 2/1/1
caller-id enable
supervisory disconnect anytone
signal groundStart
!
voice-port 3/0/0
!
voice-port 3/0/1
!
voice-port 3/1/0
!
voice-port 3/1/1
!
dial-peer cor custom
!
!
!
dial-peer voice 1 pots
destination-pattern *
direct-inward-dial
port 1/0:23
!
dial-peer voice 6000 voip
destination-pattern 6...
session target ipv4:192.168.1.240
codec g711ulaw
!
gateway
!
!
line con 0
line aux 0
password line line
speed 56000
line vty 0 4
password
login
!
end
VoiceGW#
04-17-2002 05:13 AM
i have ddi's on my gateway as well and the only difference between your dial peer and mine is i have dtmf-relay h245-alphanumeric and progress_ind setup enable 3 on them
hope this helps, also check how many digits your supplier is send you might have to do some translation if they are sending more than the 4
dave
04-17-2002 03:32 PM
thank you for your reply.
now if my service provider would get the @#%$ pri up I could actually test it
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide