07-12-2002 12:31 PM - edited 03-12-2019 07:54 PM
I am trying to figure out how to make/ensure there is ANI/Caller ID on outgoing POTS dial-peers. This has been a frustrating challenge
I have T1 E&M connections to both a voicemail (Octel) and PBX using both a 3660 and 2651 gateway.
I simply want to know two things, how can I tell that ANI is being sent and what it is.
Here is an example configuration:
cas2600#show ver
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-JS-M), Version 12.2(liszt_dev1.0.1.0), CISCO DEVELOPMENT TEST VERSION
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Mon 11-Feb-02 16:07 by shawnk
Image text-base: 0x80008088, data-base: 0x81A17AFC
ROM: System Bootstrap, Version 12.1(3r)T2, RELEASE SOFTWARE (fc1)
cas2600 uptime is 7 weeks, 1 day, 19 hours, 18 minutes
System returned to ROM by power-on
System restarted at 19:00:32 GMT Wed May 22 2002
System image file is "flash:c2600-js-mz-liszt_dev1.0.1.0.bin"
cisco 2651 (MPC860P) processor (revision 0x200) with 59392K/6144K bytes of memory.
Processor board ID JAB05410H6K (2064170137)
M860P processor: part number 5, mask 2
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
Primary Rate ISDN software, Version 1.1.
2 FastEthernet/IEEE 802.3 interface(s)
2 Channelized T1/PRI port(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
cas2600#show run
Building configuration...
Current configuration : 6504 bytes
!
! Last configuration change at 09:15:13 GMT Fri Jul 12 2002
! NVRAM config last updated at 16:45:33 GMT Wed Jun 26 2002
!
version 12.2
no parser cache
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname cas2600
!
boot system flash c2600-js-mz-liszt_dev1.0.1.0.bin
no logging buffered
logging console emergencies
enable secret 5 --moderator edit--
enable password gw2600
!
clock timezone GMT -8
voice-card 1
!
ip subnet-zero
!
!
ip ftp username root
ip ftp password password
ip domain-name sylantrolab.com
ip name-server 172.16.x.x
ip name-server 172.16.x.x
name-server 172.16.x.x
ip name-server 172.16.x.x
!
isdn switch-type primary-5ess
!
!
!
voice service voip
h323
!
voice class codec 1
codec preference 1 g711ulaw
!
!
!
!
!
!
!
no voice hpi capture buffer
no voice hpi capture destination
!
fax interface-type fax-mail
mta receive maximum-recipients 0
!
controller T1 1/0
framing sf
clock source internal
linecode ami
ds0-group 0 timeslots 1-22 type e&m-wink-start
ds0-group 1 timeslots 23-24 type e&m-wink-start
description Octel VM
!
controller T1 1/1
framing esf
clock source internal
linecode b8zs
cablelength short 133
ds0-group 0 timeslots 1-24 type e&m-wink-start
description Chatterbox
!
translation-rule 1
Rule 1 null null
!
!
!
!
interface Tunnel1
no ip address
!
interface FastEthernet0/0
ip address 172.16.x.x 255..255.255.0
duplex auto
speed auto
no cdp enable
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
no cdp enable
!
interface Dialer100
no ip address
no ip mroute-cache
no cdp enable
!
ip default-gateway 172.16.x.x
ip classless
ip route profile
no ip http server
ip pim bidir-enable
!
!
no cdp run
!
!
call rsvp-sync
!
!
voice-port 1/0:0
output attenuation 3
echo-cancel coverage 32
timing clear-wait 1000
timing wink-duration 250
timing hookflash-in 600
station-id name Octel VM
station-id number xxxxxxxxxx
!
voice-port 1/0:1
output attenuation 3
echo-cancel coverage 32
timing clear-wait 1000
timing wink-duration 250
timing hookflash-in 600
station-id name MWI
station-id number xxxxxxxxxx
!
voice-port 1/1:0
output attenuation 3
echo-cancel coverage 32
timing clear-wait 1000
timing wink-duration 250
timing hookflash-in 600
station-id name chatterbox
station-id number xxxxxxxxxx
!
mgcp ip qos dscp cs5 media
mgcp ip qos dscp cs3 signaling
no mgcp timer receive-rtcp
!
mgcp profile default
!
dial-peer cor custom
!
!
!
dial-peer voice 5000 voip
preference 1
application castransfer
incoming called-number 5[1-4].%
destination-pattern [2-9]......T
progress_ind setup enable 3
voice-class codec 1
session protocol sipv2
session target sip-server
dtmf-relay rtp-nte
no vad
!
dial-peer voice 5010 voip
description MWI CAS
preference 1
application castransfer
destination-pattern *9[4-5]....
voice-class codec 1
session protocol sipv2
session target ipv4:172.16.x.x
dtmf-relay rtp-nte
no vad
!
dial-peer voice 5020 voip
description cas to pri call
preference 1
application castransfer
destination-pattern 1..........
voice-class codec 1
session protocol sipv2
session target ipv4:172.16.x.x
dtmf-relay rtp-nte
no vad
!
dial-peer voice 1010 pots
preference 2
application session
destination-pattern xxxx
port 1/0:0
!
dial-peer voice 1020 pots
preference 2
application session
destination-pattern xxxxxx
port 1/0:0
!
dial-peer voice 1030 pots
preference 2
application session
destination-pattern xxxxxxxxxx
port 1/0:0
!
dial-peer voice 1040 pots
description CAS VM integration
preference 2
application castransfer
destination-pattern 51.%
no digit-strip
port 1/0:0
!
dial-peer voice 1050 pots
description CAS VM integration
preference 2
application castransfer
destination-pattern 52....
no digit-strip
port 1/0:0
!
dial-peer voice 1060 pots
description CAS VM integration
preference 2
application castransfer
destination-pattern 53....
no digit-strip
port 1/0:0
!
dial-peer voice 1070 pots
description CAS VM integration
preference 2
application castransfer
destination-pattern 54....
no digit-strip
port 1/0:0
!
dial-peer voice 1080 pots
preference 2
application session
destination-pattern xxxx
port 1/1:0
!
dial-peer voice 1090 pots
preference 2
application session
destination-pattern xxxxxxxx
port 1/1:0
!
dial-peer voice 2000 pots
preference 2
application session
destination-pattern xxxxxxxxxx
port 1/1:0
!
gateway
!
sip-ua
max-forwards 2
retry invite 7
retry response 7
retry bye 7
retry cancel 7
timers trying 1000
timers expires 300000
timers connect 1000
timers disconnect 1000
no oli
sip-server ipv4:172.16.x.x
!
!
line con 0
exec-timeout 0 0
line aux 0
line vty 0 4
exec-timeout 0 0
password --moderator edit--
login
!
no scheduler allocate
ntp clock-period 17180508
ntp server 172.16.x.x
!
end
07-21-2002 07:34 PM
Since there has been no response to your post, it appears to be either too complex or too rare an issue for other forum members to assist you. If you don't get a suitable response to your post, you may wish to review our resources at the online Technical Assistance Center (http://www.cisco.com/tac) or speak with a TAC engineer. You can open a TAC case online at http://www.cisco.com/tac/caseopen
If anyone else in the forum has some advice, please reply to this thread.
Thank you for posting.
07-21-2002 07:57 PM
E&M Wink does not support Caller-ID. E&M Feature Group D does, but that's basically like ISDN PRI and usually costs as much if not more that PRI.
07-31-2002 11:28 AM
Thanks. I worked out that I have to configure the 2600 trunks and E&M-FGD. Unfortunately, the gateway does not provide dial-tone when configured as E&M-FGD.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: