Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

ISDN BRI Causes

Hi,

I have problem with sending causes (User busy, Unallocated/unassigned number) to PSTN via ISDN BRI interface.

In IOS 12.4 gateway 2811 sends:

Feb 20 17:41:25.259 MET: ISDN Se0/0/0:15 Q931: TX -> DISCONNECT pd = 8 callref = 0x98E8

       Cause i = 0x8081 - Unallocated/unassigned number

In IOS 15 gateway 2911 sends:

Feb 20 16:47:29.230: ISDN BR0/2/1 Q931: TX -> PROGRESS pd = 8 callref = 0x8B

       Cause i = 0x8181 - Unallocated/unassigned number

       Progress Ind i = 0x8188 - In-band info or appropriate now available

I have problem with this behavior, because my telephony provider doesn't accept causes in PI, so calling party hear only silence. Is it possible change behavior of 2911 gateway for sending DISCONNECT and Cause instead PROGRESS and Cause.

Thank you,

Jaroslav

Everyone's tags (2)
12 REPLIES
Hall of Fame Super Gold

ISDN BRI Causes

Can you include relevant configuration ?

New Member

ISDN BRI Causes

Hi,

there is configuration. My problem is, that if gateway (2911) receive SETUP message to unallocated number, it sends this information is PROGRESS messages but I need DISCONNECT message.

version 15.1

service timestamps debug datetime msec

service timestamps log datetime msec

service password-encryption

!

hostname Router_20

!

boot-start-marker

boot system flash c2900-universalk9-mz.SPA.151-3.T2.bin

boot-end-marker

!

logging buffered 32000

enable secret XXX

!

no aaa new-model

network-clock-participate wic 0

!

no ipv6 cef

no ip source-route

ip cef

!

no ip domain lookup

ip domain name yourdomain.com

multilink bundle-name authenticated

!

isdn switch-type basic-net3

!

crypto pki token default removal timeout 0

!

voice-card 0

!

license udi pid CISCO2911/K9 sn XXX

hw-module pvdm 0/0

!

hw-module pvdm 0/1

!

hw-module sm 1

!

redundancy

!

interface GigabitEthernet0/0

ip address X.X.X.X X.X.X.X

duplex auto

speed auto

!

interface GigabitEthernet0/1

no ip address

shutdown

duplex auto

speed auto

!

interface GigabitEthernet0/2

no ip address

shutdown

duplex auto

speed auto

!

interface BRI0/2/0

no ip address

isdn switch-type basic-net3

isdn point-to-point-setup

isdn incoming-voice voice

isdn sending-complete

isdn static-tei 0

!

interface BRI0/2/1

no ip address

isdn switch-type basic-net3

isdn point-to-point-setup

isdn incoming-voice voice

isdn sending-complete

isdn static-tei 0

!

interface SM1/1

shutdown

!

ip forward-protocol nd

!

no ip http server

no ip http secure-server

!

control-plane

!

voice-port 0/0/0

compand-type a-law

cptone CZ

!

voice-port 0/0/1

!

voice-port 0/0/2

!

voice-port 0/0/3

!

voice-port 0/2/0

compand-type a-law

cptone CZ

!

voice-port 0/2/1

compand-type a-law

cptone CZ

!

mgcp profile default

!

dial-peer voice 100 pots

description <----- Outgoing call to ISDN (PSTN)

destination-pattern 0T

port 0/2/0

!

dial-peer voice 101 pots

description <----- Incomming call from ISDN (PSTN)

incoming called-number .

direct-inward-dial

!

dial-peer voice 200 pots

huntstop

destination-pattern 482428137$

port 0/0/0

!

gatekeeper

shutdown

!

line con 0

logging synchronous

line aux 0

line vty 0 4

password XxX

logging synchronous

login

transport input telnet ssh

!

scheduler allocate 20000 1000

end

Hall of Fame Super Gold

ISDN BRI Causes

Is this for CME, or CUCME ? if the latter, where's the voip DP config ?

New Member

ISDN BRI Causes

Hi,

This isn’t CUCM or CME. GW has one ISDN card (2 ports) and one FXS card (4 ports). One port of ISDN card is connected to the PSTN (telephony provider) and FXS card has connected analog phones. If GW received SETUP message from PSTN to number, which isn’t allocated, GW sends PROGRESS message with “Unallocated/unassigned number” cause to the PSTN. But I need send DISCONNECT message to the PSTN (as on 2800 ISR).

Dial-peers:

DP 100 – Outgoing DP to the PSTN

DP 101 – Incomming DP from PSTN (with direct-inward dial option)

DP 200 – Analog phone connected to the FXS card

Hall of Fame Super Gold

ISDN BRI Causes

It should be the default, but can you try

conf t

no voice call convert-discpi-to-prog

And, can you specify the exact IOS are you using.

Anyway I think the problem should not be a major one, because I don't see a reason why people should be calling your unallocated numbers .

Cisco Employee

ISDN BRI Causes

Hi

seems like some kind of announcement being played out.

please try removing any annuniciators if any in the call flow.

try changing the isdn switch type and check

Though does not seem tiyou may also try the following comand :


Hall of Fame Super Gold

ISDN BRI Causes

Amit Sharma wrote:

Hi

seems like some kind of announcement being played out.

please try removing any annuniciators if any in the call flow.

try changing the isdn switch type and check

Though does not seem tiyou may also try the following comand :


Why on earth should the switch type being changed when is correct ?

What annunciator are yout taling about ??

Do you understand the OP problem ???

ISDN BRI Causes

Thankyou Amit for indentifying the issue in One (1) Go.I had a  similar issue which was rectified by this same resolution.

Thankyou jaroslav for checking your configuration where the TCL/IVR SCRIPT which was in the call flow. Making it relevent and sensible.

Appreciate everyone's view.

ISDN BRI Causes

can you please show the call flow and the show run of the  of the existing 2811 where its working fine.

New Member

ISDN BRI Causes

I’m sorry for this topic. Problem isn’t in ISRG2, but in TCL application, which is in call path. If I stopped it, ISR and ISRG2 have same (correct) behavour.

Hall of Fame Super Gold

ISDN BRI Causes

Thanks for the clarification. Noticeably, no application configuration was present in the config you sent before.

Anyway, it should be possible to code the TCL/IVR script to behave as desired.

Please remember to rate useful posts clicking on the stars below.

ISDN BRI Causes

No issues jaroslav. we are always there to help  you out !!! .. Amit you were right here..... Kudos!!!

1021
Views
0
Helpful
12
Replies