07-14-2003 07:49 AM - edited 03-13-2019 12:43 AM
Hello,
I have tried about every variation of ISDN config and cannot get the incoming setups to work. As far as I know now it is telling me blah about the bearer cap but I thought that was usually for a voice call coming in on a data line.
Anythoughts would help.
ul 14 15:39:37.932: ISDN Se0:23: RX <- SETUP pd = 8 callref = 0x0279
Jul 14 15:39:37.932: Bearer Capability i = 0x8090A2
Jul 14 15:39:37.932: Channel ID i = 0xA18390
Jul 14 15:39:37.932: Calling Party Number i = 0x21, 0x83, '5555551212', Plan:ISDN, Type:National
Jul 14 15:39:37.932: Called Party Number i = 0xA1, '2345678900', Plan:ISDN, Type:National
Jul 14 15:39:37.936: ISDN Se0:23: Incoming call id = 0x02CF, dsl 0
Jul 14 15:39:37.936: ISDN Se0:23: NegotiateBchan: bchan 16 intid 0 serv_st 0 chan_st 0 callid 0x0000 ev 0x90 n/w? 0
Jul 14 15:39:37.936: Negotiated int_id 0 bchan 0 cr=0x8279 callid=0x02CF lo_chan 16 final int_id/bchan 0/16 cause 0x0
Jul 14 15:39:37.936: ISDN Se0:23: LIF_EVENT: ces/callid 1/0x2CF CALL_INCOMING
Jul 14 15:39:37.936: ISDN Se0:23: CALL_INCOMING dsl 0 bchan 15
Jul 14 15:39:37.936: extract_sa: no 0x71 ie to extract
Jul 14 15:39:37.936: ISDN Se0:23: CALL_INCOMING: call type is VOICE ULAW, bchan = 15
Jul 14 15:39:37.936: ISDN Se0:23: Event: Received a call id 0x2CF with a bad bearercap from 9172178812 on B16
Jul 14 15:39:37.940: ISDN Se0:23: CCPRI_ReleaseCall(): bchan 16, call id 0x2CF, call type VOICE
Jul 14 15:39:37.940: CCPRI_ReleaseChan released b_dsl 0 B_Chan 16
Jul 14 15:39:37.940: ISDN Se0:23: LIF_EVENT: ces/callid 1/0x2CF CALL_CLEARED
Jul 14 15:39:37.940: ISDN Se0:23: received CALL_CLEARED call_id 0x2CF
Jul 14 15:39:37.940: no resend setup, no redial
Jul 14 15:39:37.940: no resend setup, no redial
Jul 14 15:39:37.940: ISDN Se0:23: TX -> RELEASE_COMP pd = 8 callref = 0x8279
Jul 14 15:39:37.940: Cause i = 0x80BA - Bearer capability not available
07-14-2003 08:23 AM
Forgot conf
!AS5300 ISDN FAS-----
isdn switch-type primary-5ess
isdn voice-call-failure 0
!
interface Serial0:23
no ip address
isdn switch-type primary-5ess
no cdp enable
!
07-14-2003 10:06 AM
Jason,
Have you set a voice codec statement and applied it to the incoming dial peer so the AS-5300 knows what codec it should use?
AS5300s are a little more picky than your normal gateway and take a little more setting up. Any chance you could post the whole config (passwords ommitted) so it'll be easier to tell.
Paul
07-14-2003 10:15 AM
Thanks and sure...I used the config I had from another 5300 that was pretty much the same 5ess etc so I just cut n pasted most everything. This one I think the carrier is just sending something extra or missing it (the noteable diff I see was the new carrier sends ANI)...
I pulled all the radius and access stuff because I am positive that is not part of the issue.
!
resource-pool disable
!
call rsvp-sync
clock timezone EST -5
ip subnet-zero
!
isdn switch-type primary-5ess
isdn voice-call-failure 0
!
signaling-class cas test
voice rtp send-recv
!
voice class codec 1
codec preference 1 g729r8
codec preference 2 g723r63
codec preference 3 g711ulaw
!
!
!
!
!
fax interface-type fax-mail
mta receive maximum-recipients 0
!
controller T1 0
framing esf
clock source line primary
linecode b8zs
cablelength short 133
pri-group timeslots 1-24
!
controller T1 1
framing esf
clock source line secondary 1
linecode b8zs
cablelength short 133
pri-group timeslots 1-24
!
interface Ethernet0
ip address
no ip route-cache
no ip mroute-cache
!
interface Serial0:23
no ip address
isdn switch-type primary-5ess
isdn negotiate-bchan
no cdp enable
!
interface Serial1:23
no ip address
isdn switch-type primary-5ess
isdn guard-timer 3000
isdn T203 10000
no cdp enable
!
interface FastEthernet0
ip address
duplex full
speed auto
!
interface Dialer0
no ip address
no cdp enable
!
interface Dialer1
no ip address
no cdp enable
!
ip classless
no ip http server
ip pim bidir-enable
!
logging trap debugging
!
!
voice-port 0:D
!
voice-port 1:D
!
dial-peer voice 1 pots
incoming called-number .
direct-inward-dial
!
dial-peer voice 212 voip
destination-pattern 212T
session target ipv4:
!
dial-peer voice 718 pots
destination-pattern 1718.......
port 1:D
!
alias exec u undebug all
line con 0
line aux 0
end
07-14-2003 10:29 AM
I can't see anything in your config that matches the incoming dialled digits.
You need a
dial-peer voice xx voip
destination-pattern 234T
session target ipv:
voice codec 1
type of statement. As far as I can tell your incoming calls don't go anywhere becasue you haven't told them where to go nor which codec to use.
paul
07-14-2003 11:20 AM
ok I did the voice codec as below same thing though the digits were just fakes I typed in. Here is a real example
voice class codec 2
codec preference 1 g711ulaw
codec preference 2 g711alaw
!
!
interface Serial0:23
no ip address
isdn switch-type primary-5ess
isdn negotiate-bchan
no cdp enable
!
!
dial-peer voice 212609 voip
destination-pattern 212T
voice-class codec 2
session target ipv4:
!
ul 14 18:40:23.200: ISDN Se0:23: RX <- SETUP pd = 8 callref = 0x0283
Jul 14 18:40:23.200: Bearer Capability i = 0x8090A2
Jul 14 18:40:23.200: Channel ID i = 0xA18383
Jul 14 18:40:23.200: Calling Party Number i = 0x21, 0x83, '5555551212', Plan:ISDN, Type:National
Jul 14 18:40:23.200: Called Party Number i = 0xA1, '2126093474', Plan:ISDN, Type:National
Jul 14 18:40:23.204: ISDN Se0:23: Incoming call id = 0x02D9, dsl 0
Jul 14 18:40:23.204: ISDN Se0:23: NegotiateBchan: bchan 3 intid 0 serv_st 0 chan_st 0 callid 0x0000 ev 0x90 n/w? 0
Jul 14 18:40:23.204: Negotiated int_id 0 bchan 0 cr=0x8283 callid=0x02D9 lo_chan 3 final int_id/bchan 0/3 cause 0x0
Jul 14 18:40:23.204: ISDN Se0:23: LIF_EVENT: ces/callid 1/0x2D9 CALL_INCOMING
Jul 14 18:40:23.204: ISDN Se0:23: CALL_INCOMING dsl 0 bchan 2
Jul 14 18:40:23.204: extract_sa: no 0x71 ie to extract
Jul 14 18:40:23.204: ISDN Se0:23: CALL_INCOMING: call type is VOICE ULAW, bchan = 2
Jul 14 18:40:23.204: ISDN Se0:23: Event: Received a call id 0x2D9 with a bad bearercap from 5555551212 on B3
Jul 14 18:40:23.208: ISDN Se0:23: CCPRI_ReleaseCall(): bchan 3, call id 0x2D9, call type VOICE
Jul 14 18:40:23.208: CCPRI_ReleaseChan released b_dsl 0 B_Chan 3
Jul 14 18:40:23.208: ISDN Se0:23: LIF_EVENT: ces/callid 1/0x2D9 CALL_CLEARED
Jul 14 18:40:23.208: ISDN Se0:23: received CALL_CLEARED call_id 0x2D9
Jul 14 18:40:23.208: no resend setup, no redial
Jul 14 18:40:23.208: no resend setup, no redial
Jul 14 18:40:23.208: ISDN Se0:23: TX -> RELEASE_COMP pd = 8 callref = 0x8283
Jul 14 18:40:23.208: Cause i = 0x80BA - Bearer capability not available
07-14-2003 10:43 AM
ok I did the voice codec as below same thing though the digits were just fakes I typed in. Here is a real example
voice class codec 2
codec preference 1 g711ulaw
codec preference 2 g711alaw
!
!
interface Serial0:23
no ip address
isdn switch-type primary-5ess
isdn negotiate-bchan
no cdp enable
!
!
dial-peer voice 212609 voip
destination-pattern 212T
voice-class codec 2
session target ipv4:
!
ul 14 18:40:23.200: ISDN Se0:23: RX <- SETUP pd = 8 callref = 0x0283
Jul 14 18:40:23.200: Bearer Capability i = 0x8090A2
Jul 14 18:40:23.200: Channel ID i = 0xA18383
Jul 14 18:40:23.200: Calling Party Number i = 0x21, 0x83, '5555551212', Plan:ISDN, Type:National
Jul 14 18:40:23.200: Called Party Number i = 0xA1, '2126093474', Plan:ISDN, Type:National
Jul 14 18:40:23.204: ISDN Se0:23: Incoming call id = 0x02D9, dsl 0
Jul 14 18:40:23.204: ISDN Se0:23: NegotiateBchan: bchan 3 intid 0 serv_st 0 chan_st 0 callid 0x0000 ev 0x90 n/w? 0
Jul 14 18:40:23.204: Negotiated int_id 0 bchan 0 cr=0x8283 callid=0x02D9 lo_chan 3 final int_id/bchan 0/3 cause 0x0
Jul 14 18:40:23.204: ISDN Se0:23: LIF_EVENT: ces/callid 1/0x2D9 CALL_INCOMING
Jul 14 18:40:23.204: ISDN Se0:23: CALL_INCOMING dsl 0 bchan 2
Jul 14 18:40:23.204: extract_sa: no 0x71 ie to extract
Jul 14 18:40:23.204: ISDN Se0:23: CALL_INCOMING: call type is VOICE ULAW, bchan = 2
Jul 14 18:40:23.204: ISDN Se0:23: Event: Received a call id 0x2D9 with a bad bearercap from 5555551212 on B3
Jul 14 18:40:23.208: ISDN Se0:23: CCPRI_ReleaseCall(): bchan 3, call id 0x2D9, call type VOICE
Jul 14 18:40:23.208: CCPRI_ReleaseChan released b_dsl 0 B_Chan 3
Jul 14 18:40:23.208: ISDN Se0:23: LIF_EVENT: ces/callid 1/0x2D9 CALL_CLEARED
Jul 14 18:40:23.208: ISDN Se0:23: received CALL_CLEARED call_id 0x2D9
Jul 14 18:40:23.208: no resend setup, no redial
Jul 14 18:40:23.208: no resend setup, no redial
Jul 14 18:40:23.208: ISDN Se0:23: TX -> RELEASE_COMP pd = 8 callref = 0x8283
Jul 14 18:40:23.208: Cause i = 0x80BA - Bearer capability not available
07-14-2003 12:10 PM
Hi
A couple of remarks. If you decode the bearer capability you get this
Information Transfer Capability:
Speech
Transfer Mode:
Circuit Mode
Information Transfer Rate:
64 Kbps
User Information Layer 1 Protocol:
G.711 u-Law Speech
Also a Paul pointed out your voip peer is not correct:
dial-peer voice 212609 voip
destination-pattern 212T
voice-class codec 2
session target ipv4:
You need to have an ip address of ccm specified for this command: session target ipv4
like session target ipv4:10.48.80.41
Ullie
07-14-2003 12:16 PM
.
07-14-2003 06:52 PM
Try adding isdn incoming-voice voice to interface Serial 0:23.
Also, look at show version and make sure you have some voice resources listed.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide