cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
892
Views
0
Helpful
3
Replies

Issue after upgrading IOS

Mohamed Sherif
Level 1
Level 1

Hi All,

I was trying to upgrade a voice gateway AS5350XM from 12.4T(20)T4 to 15.1(1)T5 and the voice gateways loaded with the new IOS, however the voice-port configuration gone. I tried to configure the connection plar under voice-port but I got below error

connection plar is not allowed on NP DFC

Any idea???

Regards,

M.Sherif

3 Replies 3

paolo bevilacqua
Hall of Fame
Hall of Fame

You can use a translatio rule to translate all called number to the destination that you want.

Hi Paolo,

I already tried the translation rule but it didn't work, kindly check below configuration and debug

voice translation-rule 2

rule 1 /.*/ /9344/

!

!

voice translation-profile Divert1

translate called 2

!

voice-port 3/0:0

translation-profile incoming Divert1

!

HOIPCCVG2#test voice translation-rule 2 5

Matched with rule 1

Original number: 5      Translated number: 9344

Original number type: none      Translated number type: none

Original number plan: none      Translated number plan: none

HOIPCCVG2#

HOIPCCVG2#

HOIPCCVG2#test voice translation-rule 2 0015

Matched with rule 1

Original number: 0015   Translated number: 9344

Original number type: none      Translated number type: none

Original number plan: none      Translated number plan: none

HOIPCCVG2#test voice translation-rule 2 920003344

Matched with rule 1

Original number: 920003344      Translated number: 9344

Original number type: none      Translated number type: none

Original number plan: none      Translated number plan: none

HOIPCCVG2#debug voip dialpeer

HOIPCCVG2#sh voic cal sum

PORT           CODEC     VAD VTSP STATE            VPM STATE

============== ========= === ==================== ======================

3/0:0.1         g711ulaw   n  S_DIGIT_COLLECT       CSM_IC7_CONNECTED      

HOIPCCVG2#debug voip dialpeer

*Oct 20 09:15:56.177: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:

   Calling Number=506184032, Called Number=9344, Voice-Interface=0x0,

   Timeout=TRUE, Peer Encap Type=ENCAP_VOICE, Peer Search Type=PEER_TYPE_VOICE,

   Peer Info Type=DIALPEER_INFO_SPEECH

*Oct 20 09:15:56.177: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:

   Result=Success(0) after DP_MATCH_INCOMING_DNIS; Incoming Dial-peer=1

*Oct 20 09:15:56.177: //-1/xxxxxxxxxxxx/DPM/dpMatchSafModulePlugin:

   dialstring=NULL, saf_enabled=0, saf_dndb_lookup=0, dp_result=0

*Oct 20 09:15:56.357: %SYS-3-INVMEMINT: Invalid memory action (malloc) at interrupt level -Traceback= 0x6394DC40z 0x620F091Cz 0x620ECD08z 0x620ECF30z 0x620ED5DCz 0x620E9E40z 0x626346CCz 0x62635408z 0x626011A0z 0x62603D70z 0x62B84D38z 0x602E42D4z 0x602E0E6Cz 0x602E1E08z 0x6026505Cz 0x60267644z

*Oct 20 09:15:56.357: %SYS-2-MALLOCFAIL: Memory allocation of 512 bytes failed from 0x620FC134, alignment 0

Pool: Processor  Free: 240350408  Cause: Interrupt level allocation

Alternate Pool: None  Free: 0  Cause: Interrupt level allocation

-Process= "", ipl= 3

*Oct 20 09:16:03.621: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:

   Calling Number=505911063, Called Number=9344, Voice-Interface=0x0,

   Timeout=TRUE, Peer Encap Type=ENCAP_VOICE, Peer Search Type=PEER_TYPE_VOICE,

   Peer Info Type=DIALPEER_INFO_SPEECH

*Oct 20 09:16:03.621: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:

   Result=Success(0) after DP_MATCH_INCOMING_DNIS; Incoming Dial-peer=1

*Oct 20 09:16:03.621: //-1/xxxxxxxxxxxx/DPM/dpMatchSafModulePlugin:

   dialstring=NULL, saf_enabled=0, saf_dndb_lookup=0, dp_result=0

*Oct 20 09:16:03.825: %SYS-3-INVMEMINT: Invalid memory action (malloc) at interrupt level -Traceback= 0x6394DC40z 0x620F091Cz 0x620ECD08z 0x620ECF30z 0x620ED5DCz 0x620E9E40z 0x626346CCz 0x62635408z 0x626011A0z 0x62603D70z 0x62B84D38z 0x602E42D4z 0x602E0E6Cz 0x602E1E08z 0x6026505Cz 0x60267644z

HOIPCCVG2#

Regards,

Mohamed Sherif

Any idea !!!

Regards,

M.Sherif