Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

MQC LLC not working with WS-X6704-10GE

I have a site trying to do the following:

service-policy output voip

and receives the following error:

priority command is not supported in output direction for this interface

I found that the WS-X6704-10GE doesn't support "priority" queing. So, what line cards will support priority queueing on a CAT 6509? Or is there another way to configure?

1 REPLY

Re: MQC LLC not working with WS-X6704-10GE

hi

you can use the following logic

interface TenGigabitEthernet1/1

wrr-queue bandwidth 5 25 20 20 20 5 5

! Sets the WRR weights for 5:25:20:20:20:5:5 (Q1 through Q7)

wrr-queue queue-limit 5 25 10 10 10 5 5

! Allocates 5% to Q1, 25% to Q2, 10% to Q3, 10% to Q4,

! Allocates 10% to Q5, 5% to Q6 and 5% to Q7

wrr-queue random-detect min-threshold 1 80 100 100 100 100 100 100 100

! Sets Min WRED Threshold for Q1T1 to 80% and all others to 100%

wrr-queue random-detect min-threshold 2 1 100 100 100 100 100 100 100

! Sets Min WRED Threshold for Q2T1 to 80% and all others to 100%

wrr-queue random-detect min-threshold 3 80 100 100 100 100 100 100 100

! Sets Min WRED Threshold for Q3T1 to 80% and all others to 100%

wrr-queue random-detect min-threshold 4 80 100 100 100 100 100 100 100

! Sets Min WRED Threshold for Q4T1 to 80% and all others to 100%

wrr-queue random-detect min-threshold 5 80 100 100 100 100 100 100 100

! Sets Min WRED Threshold for Q5T1 to 80% and all others to 100%

wrr-queue random-detect min-threshold 6 80 100 100 100 100 100 100 100

! Sets Min WRED Threshold for Q6T1 to 80% and all others to 100%

wrr-queue random-detect min-threshold 7 80 100 100 100 100 100 100 100

! Sets Min WRED Threshold for Q7T1 to 80% and all others to 100%

wrr-queue random-detect max-threshold 1 100 100 100 100 100 100 100 100

! Sets Max WRED Threshold for Q1T1 to 100% and all others to 100%

wrr-queue random-detect max-threshold 2 100 100 100 100 100 100 100 100

! Sets Max WRED Threshold for Q2T1 to 100% and all others to 100%

! All other WRED Thresholds remain at their default values (100%

wrr-queue random-detect 4 ! Enables WRED on Q4

wrr-queue random-detect 5 ! Enables WRED on Q5

wrr-queue random-detect 6 ! Enables WRED on Q6

wrr-queue random-detect 7 ! Enables WRED on Q7

wrr-queue cos-map 1 1 1 ! Maps Scavenger/Bulk to Q1

wrr-queue cos-map 2 1 0 ! Maps Best Effort to Q2

wrr-queue cos-map 3 1 4 ! Maps Video to Q3

wrr-queue cos-map 4 1 2 ! Maps Net-Mgmt/Transactional to Q4

wrr-queue cos-map 5 1 3 ! Maps Call-Signaling/MC-Data to Q5

wrr-queue cos-map 6 1 6 ! Maps IP Routing to Q6

wrr-queue cos-map 7 1 7 ! Maps STP to Q7

mls qos trust dscp ! Trusts DSCP

hope this helps

good luck

149
Views
0
Helpful
1
Replies