Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Please help with COR config question on CME

Gurus,

I have been struggling for some time to now to get COR set up properly on my CME. I did have a breakthrough when I discovered that INCOMING and OUTGOING meant from the viewpoint of the router, NOT the phone. Still I am having issues, specifically with the Dial-peer config. I find examples ranging from elaborate to simple, and don't know which to use.

I only wish to block on some instruments Long Distance (my area code is 907), international, 411,1900, and 555-1212. Please see my existing config below; could someone tell me how to configure the dial-peer portions? I get my dial tone from a PRI T1, if it makes any difference, and we dial 9 first.

Thanks,

Michael

dial-peer cor custom

name 911

name 1800

name local-call

name ld-call

name 411

name int-call

name 1900

!

!

dial-peer cor list call1800

member 1800

!

dial-peer cor list call911

member 911

!

dial-peer cor list callint

member int-call

!

dial-peer cor list callld

member ld-call

!

dial-peer cor list call411

member 411

!

dial-peer cor list localonly

member 911

member 1800

member local-call

!

dial-peer cor list call1900

member 1900

!

dial-peer cor list LongDistance

member 911

member 1800

member local-call

member ld-call

!

dial-peer cor list calllocal

member local-call

8 REPLIES

Re: Please help with COR config question on CME

apply

call1800, call911, callint, callld, call411 , calllocal COR lists in the outbound direction on respective dial-peers.

for ex:

dial-peer voice 1 pots

destination-pattern 911

no digit-strip

corlist outgoing call911

port 1/0:23

dial-peer voice 2 pots

destination-pattern 91800.......

forward-digits 11

corlist outgoing call1800

port 1/0:23

dial-peer voice 3 pots

destination-pattern 9[2-9]......

forward-digits 7

corlist outgoing calllocal

port 1/0:23

so on and so forth.

The following cor lists localonly, LongDistance etc, apply to phones as required.

ephone-dn 1

corlist incoming localonly.

So ephone-dn 1 will have access to 911, 1800 and local-calls as the corlist applied on the phone is a superset of the corlist specified on the respective dial-peers for 911, 1800 and local-calls.

HTH

Sankar

PS: please remember to rate posts!

New Member

Re: Please help with COR config question on CME

Thanks for the help!!

I've applied your config, then applied the COR to my own personal phone. I tried to dial a 9-1-903-xxx-xxxx (Texas somewhere...) and was able to do so. The COR settings should have prevented this??

This is my current config, as it applies to COR:

voice-port 0/0/0:23

dial-peer cor custom

name 911

name 1800

name local-call

name ld-call

name 411

name int-call

name 1900

!

!

dial-peer cor list call1800

member 1800

!

dial-peer cor list call911

member 911

!

dial-peer cor list callint

member int-call

!

dial-peer cor list callld

member ld-call

!

dial-peer cor list call411

member 411

!

dial-peer cor list localonly

member 911

member 1800

member local-call

!

dial-peer cor list call1900

member 1900

!

dial-peer cor list LongDistance

member 911

member 1800

member local-call

member ld-call

!

dial-peer cor list calllocal

member local-call

!

!

dial-peer voice 20 pots

corlist outgoing call911

destination-pattern 911

no digit-strip

port 0/0/0:23

!

dial-peer voice 21 pots

corlist outgoing call1800

destination-pattern 91800.......

port 0/0/0:23

forward-digits 11

!

dial-peer voice 22 pots

corlist outgoing calllocal

destination-pattern 9[2-9]......

port 0/0/0:23

forward-digits 7

!

!

ephone-dn 4 dual-line

number 3809

label Mike 3809

description Michael Albert

name Michael Albert

call-forward busy 3801

call-forward noan 3801 timeout 15

corlist outgoing localonly

Thanks again for your help,

Michael

New Member

Re: Please help with COR config question on CME

Hi Mike,

I don't see your dial-peer for Long distance.

Try something like:

dial-peer voice 23 pots

corlist outgoing callld

destination-pattern 91..........

port 0/0/0:23

forward-digits 11

You will probably also need a similar dial-peer for International:

dial-peer voice 24 pots

corlist outgoing callint

destination-pattern 9011.T

port 0/0/0:23

prefix 011

Also, you need to apply the corlist for your phone in incoming direction:

ephone-dn 4 dual-line

number 3809

label Mike 3809

description Michael Albert

name Michael Albert

call-forward busy 3801

call-forward noan 3801 timeout 15

corlist incoming localonly

Hope this helps,

Val

Re: Please help with COR config question on CME

Val is right.

You are missing a dial-peer for long distance.

New Member

Re: Please help with COR config question on CME

This is my current config:

dial-peer cor custom

name 911

name 1800

name local-call

name ld-call

name 411

name int-call

name 1900

!

!

dial-peer cor list call1800

member 1800

!

dial-peer cor list call911

member 911

!

dial-peer cor list callint

member int-call

!

dial-peer cor list callld

member ld-call

!

dial-peer cor list call411

member 411

!

dial-peer cor list localonly

member 911

member 1800

member local-call

!

dial-peer cor list call1900

member 1900

!

dial-peer cor list LongDistance

member 911

member 1800

member local-call

member ld-call

!

dial-peer cor list calllocal

member local-call

dial-peer voice 20 pots

corlist outgoing call911

destination-pattern 911

no digit-strip

port 0/0/0:23

!

dial-peer voice 21 pots

corlist outgoing call1800

destination-pattern 91800.......

port 0/0/0:23

forward-digits 11

!

dial-peer voice 22 pots

corlist outgoing calllocal

destination-pattern 9[2-9]......

port 0/0/0:23

forward-digits 7

!

dial-peer voice 23 pots

corlist outgoing callld

destination-pattern 91..........

port 0/0/0:23

forward-digits 11

!

dial-peer voice 24 pots

corlist outgoing callint

destination-pattern 9011.T

port 0/0/0:23

prefix 011

ephone-dn 4 dual-line

number 3809

label Mike 3809

description Michael Albert

name Michael Albert

call-forward busy 3801

call-forward noan 3801 timeout 15

corlist incoming localonly

Still I am able to dial a long-distance number (9-1-903-xxx-xxxx). Does this config look good to you?

Thanks,

Michael

New Member

Re: Please help with COR config question on CME

Are you sure you are matching only dial-peer 23 with this number.

How did you dial the Texas number before adding the LD dial peer?

Do you have other PSTN trinks on this router?

Please paste the whole config for the router.

V.

New Member

Re: Please help with COR config question on CME

I was hoping you'd ask that. I wondered if I had something else going on that was screwing things up.

Thanks for the time!

New Member

Re: Please help with COR config question on CME

Greetings,

The config looks OK in the COR piece.

I don't see an obvious reason for your issues.

Try "debug voip ccapi inout" and make sure that the called LD number matches dial-peer 24. There are potentially few matches with dial-peer 24 being the longest one but just in case try to verify this.

Also try "debug ephone detail".

If you could afford it you can try to reload the router with just basic config and COR, no translation rules and other dial-peers for incoming numbers, and give it a try again.

You can also try another phone with "corlist incoming calllocal" and you shouldn't be able to call 1800 as well.

Good luck!

Val.

184
Views
0
Helpful
8
Replies
CreatePlease to create content