Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

Problem calling from CME to CCM

Hi,

I have a few sites running CME 4.0 and a couple of sites with CCM4.1. I would like to be able to call between CME and CCM. Calling from the CCM's to the CME's using an ICT works fine, but cannot call the other way. CME's can talk to each other though.

Any help would be appreciated.

Thanks

Tony

12 REPLIES
Hall of Fame Super Silver

Re: Problem calling from CME to CCM

Can you post your CME config?

Couple of things to make sure:

voip dial-peers are pointing to the correct IP address

The ICT trunk has CSS applied with access to phone's partition.

Chris

New Member

Re: Problem calling from CME to CCM

Hi,

The dial-peer is pointing the to Pub,( have tried the sub but same problem).

The ICT has a CSS in which all partitions reside. Important parts of the config below:-

isdn switch-type primary-ni

voice-card 0

no dspfarm

!

!

!

voice call send-alert

voice rtp send-recv

!

voice service voip

allow-connections h323 to h323

allow-connections h323 to sip

allow-connections sip to h323

no supplementary-service h450.2

no supplementary-service h450.3

supplementary-service h450.12

fax protocol pass-through g711ulaw

h323

h225 h245-address on-connect

modem passthrough nse payload-type 101 codec g711ulaw

!

!

voice class codec 1

codec preference 1 g711alaw

codec preference 2 g711ulaw

codec preference 3 g729r8

!

!

!

voice class h323 1

h225 h245-address on-connect

h225 h245-address facility

h225 h245-address progress

h225 h245-address sync

call preserve

telephony-service ccm-compatible

ccm-compatible

!

!

!

dial-peer voice 4 voip

description (other CME site)

destination-pattern 25..

voice-class h323 1

session target ipv4:10.8.21.254

codec g711ulaw

no vad

!

dial-peer voice 3 voip

description (CCM 4.1 site)

destination-pattern 3...

voice-class h323 1

session target ipv4:10.9.200.1 (Pub)

no vad

codec g711ulaw

telephony-service

load 7910 P00403020214

load 7960-7940 P00305000301

load 7914 S00104000100

load 7961 TERM41.7-0-3-0S

load 7936 cmterm_7936.3-3-5-0

max-ephones 200

max-dn 200

ip source-address 10.8.97.253 port 2000

auto assign 1 to 200

timeouts interdigit 4

url information http://10.8.97.253/localdirectory

url directories http://10.8.97.253/localdirectory

url services http://10.8.97.253/localdirectory

url authentication http://10.8.97.251/voiceview/authentication/authentic

time-zone 8

voicemail 1755

max-conferences 12 gain -6

moh music-on-hold.au

web admin system name **** password ****

web admin customer name *** password ***

dn-webedit

time-webedit

transfer-system full-consult

transfer-pattern .T

create cnf-files version-stamp 7960 Nov 02 2006 14:06:18

Thanks

Tony

New Member

Re: Problem calling from CME to CCM

You need this configured

h323-gateway voip bind srcaddr x.x.x.x

Re: Problem calling from CME to CCM

Just like Junfeng said,

If your ICT trunk has 1.1.1.1 as the ip address configured, go under the specific interface in CME router with the same ip address and give the h323 bind command.

HTH

Sankar

New Member

Re: Problem calling from CME to CCM

Guys,

It is already configured on the interface.

interface GigabitEthernet0/0.1

description DATA VLAN

encapsulation dot1Q 197

ip address 10.1.97.253 255.255.255.0

arp timeout 300

!

interface GigabitEthernet0/0.2

description VOICE VLAN

encapsulation dot1Q 897

ip address 10.8.97.253 255.255.255.0

arp timeout 300

h323-gateway voip bind srcaddr 10.8.97.253

Thanks

Tony

Hall of Fame Super Silver

Re: Problem calling from CME to CCM

You are missing this command under Gi0/0.2

h323-gateway voip interface

Also, you are forcing the codec to G.711 in the dial-peer, how is the trunk configured in CCM, what is the region referenced by the device pool configured to use between other regions? If it is G.729 the call will fail, unless you have a MRGL with transcoder applied to the Trunk (not device pool).

Your best option is to create voice codec class with codec preferences and apply to dial-peer.

Chris

Blue

Re: Problem calling from CME to CCM

do you have the correct outbound dialPeers for calls from the CME to the CCMs?

please paste your config, minus any sensative IP addys, and we can better help you.

Silver

Re: Problem calling from CME to CCM

In the ICT configuration, do you have MTP Required Checked? If yes, can you uncheck that and reset the ICT and see if that helps.

Also how about the Enable Inbound Faststart check box?

Regards,

Anup

New Member

Re: Problem calling from CME to CCM

yep, tried both them but no change.

I have run some traces, i can see the CME router matching the correct dial-peer, but the call does not reach the CCM's. From the CME router i can ping the CCM;s and the CCM registered Ip Phones. From the CCM I can ping the CME registered phones.

thanks

Tony

New Member

Re: Problem calling from CME to CCM

Have you tried nixing the ICT and making the connection an h.323 gateway instead?

Also you might try pointing to one of the subs just to see if it works. mtp and/or media resources might be screwed up.

Also try "incoming called-number " and see if that matches better.

New Member

Re: Problem calling from CME to CCM

Have you tried nixing the ICT and making the connection an h.323 gateway instead?

****TRIED THAT ALREADY****

Also you might try pointing to one of the subs just to see if it works. mtp and/or media resources might be screwed up.

****TRIED THAT ALREADY****

Also try "incoming called-number " and see if that matches better.

****NOT TRIED THAT. WILL GIVE IT GO.***

THANKS

TONY

New Member

Re: Problem calling from CME to CCM

Icoming called number 3040 (my ext) didnt make any difference.

thanks

Tony

314
Views
0
Helpful
12
Replies
CreatePlease to create content