Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

Problems on integration XMedius Fax Server with NEC Univerge 2000 IPS

Hello everyone

I met a problem when I integrated XMedius fax with NEC Univerge 2000 IPS thru t1 qsig.When I call the fax number, calls cut immediately

or busy signal. calls between analog and IP is ok.

NEC PABX 2000->t1->Cisco2851->XMedius fax(v5.5)/CM5

LHK2851#

043817: *Feb 5 11:21:25.203 PCTime: ISDN Se0/2/0:23 Q931: RX <- SETUP pd = 8 callref = 0x6901

Sending Complete

Bearer Capability i = 0x9090A2

Standard = CCITT

Transfer Capability = 3.1kHz Audio

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA98385

Exclusive, Channel 5

Facility i = 0x9FAA06800100820100A11C02010006052B0C090000801000000000000000000000000000000000

Progress Ind i = 0x8183 - Origination address is non-ISDN

Called Party Number i = 0x80, '799'

Plan:Unknown, Type:Unknown

Shift to Codeset 4

Codeset 4 IE 0x31 i = 0x00

Shift to Codeset 5

Codeset 5 IE 0x32 i = 0x81

043818: *Feb 5 11:21:25.203 PCTime: ISDN Se0/2/0:23 **ERROR**: isdn_init_fac_data: No Opval 0

043819: *Feb 5 11:21:25.207 PCTime: ISDN Se0/2/0:23 **ERROR**: isdn_init_fac_data: No Opval 0

043820: *Feb 5 11:21:25.215 PCTime: ISDN Se0/2/0:23 Q931: TX -> CALL_PROC pd = 8 callref = 0xE901

Channel ID i = 0xA98385

Exclusive, Channel 5

043821: *Feb 5 11:21:26.007 PCTime: %ISDN-6-CONNECT: Interface Serial0/2/0:4 is now connected to N/A N/A

043822: *Feb 5 11:21:26.011 PCTime: ISDN Se0/2/0:23 Q931: TX -> CONNECT pd = 8 callref = 0xE901

Connected Number i = 0x80, '799'

043823: *Feb 5 11:21:26.079 PCTime: ISDN Se0/2/0:23 Q931: RX <- CONNECT_ACK pd = 8 callref = 0x6901

043824: *Feb 5 11:21:31.119 PCTime: ISDN Se0/2/0:23 Q931: RX <- DISCONNECT pd = 8 callref = 0x6901

Cause i = 0x8190 - Normal call clearing

043825: *Feb 5 11:21:31.119 PCTime: %ISDN-6-CONNECT: Interface Serial0/2/0:4 is now connected to N/A N/A

043826: *Feb 5 11:21:31.119 PCTime: %ISDN-6-DISCONNECT: Interface Serial0/2/0:4 disconnected from unknown , call lasted 5 seconds

043827: *Feb 5 11:21:31.119 PCTime: ISDN Se0/2/0:23 Q931: TX -> RELEASE pd = 8 callref = 0xE901

043828: *Feb 5 11:21:31.203 PCTime: ISDN Se0/2/0:23 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x6901

Cause i = 0x819F - Normal, unspecified

LHK2851#

LHK2851#sh runn

voice call disc-pi-off

!

voice service voip

qsig decode

allow-connections h323 to h323

allow-connections h323 to sip

allow-connections sip to h323

allow-connections sip to sip

fax protocol t38 ls-redundancy 2 hs-redundancy 2 fallback cisco

h323

sip

!

voice class codec 1

codec preference 1 g711ulaw

codec preference 2 g711alaw

codec preference 3 g729br8

codec preference 4 g729r8

!

voice class h323 1

h225 timeout tcp establish 3

!

controller T1 0/2/0

framing esf

linecode b8zs

pri-group timeslots 1-24

!

interface Serial0/2/0:23

no ip address

encapsulation hdlc

isdn switch-type primary-qsig

isdn timer T310 120000

isdn overlap-receiving

isdn protocol-emulate network

isdn incoming-voice voice

isdn supp-service name calling profile Network-Extensions operation-value-tag local

isdn bchan-number-order ascending round-robin

isdn outgoing ie facility

isdn outgoing ie display

no fair-queue

no cdp enable

!

voice-port 0/2/0:23

cptone HK

!

dspfarm profile 1 conference

codec g711ulaw

codec g711alaw

codec g729ar8

codec g729abr8

codec g729r8

codec g729br8

maximum sessions 4

associate application SCCP

!

dial-peer voice 101 voip

destination-pattern 79[1,3,5,7,9]

voice-class h323 1

session target ipv4:X.X.X.X

dtmf-relay h245-alphanumeric

codec g711ulaw

fax-relay sg3-to-g3

fax rate 14400

fax nsf 000000

fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback cisco

no vad

!

Thanks in advance.

1 REPLY
New Member

Re: Problems on integration XMedius Fax Server with NEC Univerge

anyone meet the familiar things? please help.

Thanks a lot.

483
Views
0
Helpful
1
Replies
CreatePlease to create content