Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Proper command to use for modifying E/M card

Gurus,

I'm attempting to configure MOH on my CME, from a live source as documented here: http://www.cisco.com/en/US/products/sw/iosswrel/ps5207/products_administration_guide_chapter09186a00801f12fa.html.

I've got the CD player ready, have had the adapter cable built to connect it to the E/M card, but I'm not sure how to modify the E/M card with the voice-port command. The card is on a 2851 router, and it is installed in the location marked "HWLC1". I am totally unfamiliar with this aspect, an am not sure what I should use (eg., voice-port 1/1/0, etc).

Any help woudl be greatly appreciated.

4 REPLIES

Re: Proper command to use for modifying E/M card

Once your router detects the VIC, it should appear in the config (sh run) as voice-port a/x/y. a, x and y can vary based on slot, port etc.

to configure e/m to support MOh, you will need to do the following,

voice-port 1/1/0 <-- e/m port 0 on slot 1.

auto-cut-through

signal immediate

operation 4-wire

input gain

dial-peer voice 1 pots

destination-pattern

port 1/1/0 <-- this needs to be e/m port

ephone-dn 1

number 3333

moh out-call

New Member

Re: Proper command to use for modifying E/M card

Hi, I have the following listed in my show run:

voice-port 0/0/0:23

!

voice-port 0/1/0

!

voice-port 0/1/1

!

voice-port 0/2/0

!

voice-port 0/2/1

!

voice-port 0/2/2

!

voice-port 0/2/3

!

voice-port 0/3/0

!

voice-port 0/3/1

!

voice-port 0/3/2

!

voice-port 0/3/3

So just so I understand, 'slot 1' (the middle number of the three) would refer to the actual location on the router marked HWLC1? So likewise, slot 2 or 3 would refer to the locations HWLC-2 and -3?

Re: Proper command to use for modifying E/M card

I see that you have many voice ports and you are trying to identify which port is e/m. You can do a show voice-port a/x/y to find out which port is e/m.

You can also do a sh voice-port summary to find out the interface types on each vic.

From your port numbering, you seem to have ,

a. 1 port t1 vwic on slot 0,

b. 2 port vic on slot 1,

c. 4 port vic on slot 2 and

d. 4 port vic on slot 3.

Most likely your slot 1 (2 port vic) should be e/m.

Do a show voice-port 0/1/0 or (0/1/1) to find out what kind of interface it is.

HTH

Sankar.

PS: please remember to rate posts!

New Member

Re: Proper command to use for modifying E/M card

The router is in a different location, but I wrote down what I have:

HWLC0: VWIC2-1MFT (T1 interface card)

HWLC1: VIC2 e/m card

HWLC2 & 3:VIC2-4FXO cards (not in use)

Thanks for the advice!!

131
Views
5
Helpful
4
Replies
CreatePlease to create content