Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

PSTN Simulator Issues

Hi.

I'm implementing a 2801 as pstn simulator, i have another two 1760 acting as branch rtr with an fxs phone each one.

When a make a call between the 1760 the remote fxs phone doesn't ring and in the calling phone i only hear a dial tone but after 15 - 17 seconds i recieve fast busy tone.

Can anyone help me to see if a missed or fail with something in the conf.

Thnks

 

pstn-simulator#sh run
Building configuration...


Current configuration : 1996 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname pstn-simulator
!
boot-start-marker
boot-end-marker
!
card type t1 0 2
!
network-clock-participate wic 2 
dot11 syslog
ip source-route
!
isdn switch-type primary-ni
!
voice-card 0
!
controller T1 0/2/0
 cablelength long 0db
 pri-group timeslots 1-10,24
 description TRONCAL - AUTOMOTRIZ MONTERREY
!
controller T1 0/2/1
 cablelength long 0db
 pri-group timeslots 1-10,24
 description TRONCAL - AUTOMOTRIZ NOGALES
!
interface Serial0/2/0:23
 description TRONCAL - AUTOMOTRIZ MONTERREY
 no ip address
 encapsulation hdlc
 isdn switch-type primary-ni
 isdn protocol-emulate network
 isdn incoming-voice voice
 no cdp enable
!
interface Serial0/2/1:23
 description TRONCAL - AUTOMOTRIZ NOGALES
 no ip address
 encapsulation hdlc
 isdn switch-type primary-ni
 isdn protocol-emulate network
 isdn incoming-voice voice
 no cdp enable
!
!
!
voice-port 0/2/0:23
!
voice-port 0/2/1:23
!
ccm-manager fax protocol cisco
!         
dial-peer voice 10 pots
 destination-pattern 018115501...
 port 0/2/0:23
 prefix 8115501
!
dial-peer voice 11 pots
 destination-pattern 016188172...
 port 0/2/1:23
 prefix 6188172
!

pstn-simulator#

 

 

BR1#sh run
Building configuration...

Current configuration : 1418 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname BR1
!
tdm clock T1 1/0 both export line
voice-card 1
!
voice-card 3
!
isdn switch-type primary-ni
!
controller T1 1/0
 framing esf
 linecode b8zs
 cablelength long 0db
 pri-group timeslots 1-10,24
!
interface Serial1/0:23
 no ip address
 encapsulation hdlc
 no logging event link-status
 isdn switch-type primary-ni
 isdn incoming-voice voice
 no cdp enable
!
voice-port 3/0
 cptone MX
 station-id number 8115501000
!
voice-port 3/1
!
voice-port 1/0:23
!
dial-peer voice 1 pots
 incoming called-number 8115501...
 direct-inward-dial
 port 1/0:23
!
dial-peer voice 1000 pots
 destination-pattern 8115501000
 port 3/0
!
dial-peer voice 901 pots
 destination-pattern 01..........
 port 1/0:23
 prefix 01
!
BR1#

 

Building configuration...

Current configuration : 1417 bytes
!
version 12.4
!
hostname BR2
!

!
card type t1 1
!
memory-size iomem 5
tdm clock T1 1/0 both export line
voice-card 1
!
voice-card 3
!
isdn switch-type primary-ni
!
controller T1 1/0
 framing esf
 linecode b8zs
 cablelength long 0db
 pri-group timeslots 1-10,24
!         
interface Serial1/0:23
 no ip address
 encapsulation hdlc
 no logging event link-status
 isdn switch-type primary-ni
 isdn incoming-voice voice
 no cdp enable
!
voice-port 3/0
 cptone MX
 station-id number 2800
!
voice-port 3/1
!
voice-port 1/0:23
!
dial-peer voice 901 pots
 destination-pattern 01..........
 port 1/0:23
 forward-digits all
!
dial-peer voice 1 pots
 incoming called-number 6188172...
 direct-inward-dial
 port 1/0:23
!
dial-peer voice 1000 pots
 destination-pattern 6188172800
 port 3/0
!
BR2#

When  i try a call in the pstn i see this logs, and ipm not sure if this right see the same channel:

 

pstn-simulator#
*Apr  6 21:24:03.911: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
   Calling Number=8115501000, Called Number=016188172800, Voice-Interface=0x66C83310,
   Timeout=TRUE, Peer Encap Type=ENCAP_VOICE, Peer Search Type=PEER_TYPE_VOICE,
   Peer Info Type=DIALPEER_INFO_SPEECH
*Apr  6 21:24:03.911: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
   Result=Success(0) after DP_MATCH_PORT; Incoming Dial-peer=11
*Apr  6 21:24:03.911: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
   Calling Number=8115501000, Called Number=016188172800, Voice-Interface=0x0,
   Timeout=TRUE, Peer Encap Type=ENCAP_VOICE, Peer Search Type=PEER_TYPE_VOICE,
   Peer Info Type=DIALPEER_INFO_FAX
*Apr  6 21:24:03.911: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
   Result=NO_MATCH(-1) After All Match Rules Attempt
*Apr  6 21:24:03.911: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
   Calling Number=8115501000, Called Number=016188172800, Voice-Interface=0x0,
   Timeout=TRUE, Peer Encap Type=ENCAP_VOICE, Peer Search Type=PEER_TYPE_VOICE,
   Peer Info Type=DIALPEER_INFO_SPEECH
*Apr  6 21:24:03.911: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
   Result=NO_MATCH(-1) After All Match Rules Attempt
*Apr  6 21:24:03.915: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
   Calling Number=8115501000, Called Number=016188172800, Voice-Interface=0x66C83310,
   Timeout=TRUE, Peer Encap Type=ENCAP_VOICE, Peer Search Type=PEER_TYPE_VOICE,
   Peer Info Type=DIALPEER_INFO_SPEECH
*Apr  6 21:24:03.915: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:
   Result=Success(0) after DP_MATCH_PORT; Incoming Dial-peer=11
*Apr  6 21:24:03.923: %ISDN-6-CONNECT: Interface Serial0/2/1:9 is now connected to 8115501000 N/A
*Apr  6 21:24:03.927: %ISDN-6-CONNECT: Interface Serial0/2/1:9 is now connected to 8115501000 N/A
*Apr  6 21:24:21.679: %ISDN-6-DISCONNECT: Interface Serial0/2/1:9  disconnected from 8115501000 , call lasted 17 seconds
pstn-simulator#

 

Thnks

Everyone's tags (1)
1 ACCEPTED SOLUTION

Accepted Solutions

Hi. This is the log output

Hi. This is the log output:

Calling Number=8115501000, Called Number=016188172800

Incoming Dial-peer=11

Result=NO_MATCH(-1) After All Match Rules Attempt

 

The call uses dp 11 as incoming dp but are "looped" to dp 11.

Try to invert "port" in dp 10 and 11.

 

Regards.

 

 

 

2 REPLIES

Hi. This is the log output

Hi. This is the log output:

Calling Number=8115501000, Called Number=016188172800

Incoming Dial-peer=11

Result=NO_MATCH(-1) After All Match Rules Attempt

 

The call uses dp 11 as incoming dp but are "looped" to dp 11.

Try to invert "port" in dp 10 and 11.

 

Regards.

 

 

 

New Member

That was the problem, only

That was the problem, only invert the port and work fine !

 

Thnks.

383
Views
0
Helpful
2
Replies
CreatePlease to create content